Bedienungsanleitung Turmix A31122 (Seite 21 von 28) (Deutsch, Englisch, Französisch, Italienisch)

485270

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Overview

1. Driving unit with rubber handle

2. Immersion mixer

– Attach mixer from below onto the driving unit.

– Insert the immersion mixer on the driving unit

turning it until it clicks.

– The mixer may not be used directly in pots.

3. On/off switch

It works only if the safety button is pressed (4).

– To switch on the appliance keep the switch

pressed down (if you release it, the mixer will turn

off automatically for safety reasons).

–

If the appliance is turned on when the battery

charger is down, a safety device automatically

turns it off. The LED display starts flashing (5).

After it turns off automatically, do not press down

on the On/Off button (3), otherwise the accumula-

tor might be damaged.

4. Safety button

The safety button avoids that one accidentally turns

on the appliance.

– To turn the appliance ON, press down on the safe-

ty button and the On/Off switch (3). While the mix-

er is working one can release the safety button.

5. Battery Charger - Led Display

While the appliance is being used, the battery charge

status is displayed by the LED (the appliance is not

connected to the battery charger):

– press the safety button (4.)

–

LED is lit = Battery full

–

LED flashes slowly = Battery half fulll

–

LED flashes quickly = Battery almost empty

–

Before using the appliance for the first time, fully

charge the base unit (approx. 2 hours).

6. Blending cup with lid

– Place the cup on a flat surface.

– To avoid spurts, immerge mixer completely before

pressing down on the ON button.

– For better results blend small portions.

– To preserve in the fridge apply the lid onto the

blending cup.

7. After use

– First draw out the immersion mixer.

– Remove the mixer for cleaning (be careful because

the blade is very sharp; hold it only by its plastic

handle).

–

Insert the battery charger into the socket (do not

use any other battery charger!).

–

Position the driving unit on the special support.

Keep all contacts clean.

8. Battery charge status:

– LED goes out after approx. 10 seconds. = battery

full.

–

LED on = battery is charging.

–

If you don’t use the appliance for a long time,

unplug the battery charger.

Assembly

– The charging station can be placed on a flat surface

or mounted on a wall with the screws contained in

the box (not, however, over sinks, stoves or plugs).

9.-12. Assembly

– Unpack screws and screw anchors.

– Mark the holes on the wall (extract by pulling

down the assembly plate from the charging station

and use it like a template). Do not assemble over

kitchen sinks, stoves or current sockets.

– Drill creating two holes (6 mm in diameter).

– Insert screw anchors and fix the plate with the

screws ( with pins in the upward position).

– Insert the charging station from above (it clicks).

– Insert the battery charger into the socket (the

remaining cord can be wound around the two pins

of the assembly plate).

– Position the driving unit onto the special support

on the left.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Turmix A31122 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info