Bedienungsanleitung Turmix VX 250 (Seite 27 von 32) (Deutsch, Englisch, Französisch, Italienisch)

485325

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Connect the mains cable to a grounded mains socket 10.

Press the on/off switch 11.

The green power on lamp and the yellow steam generator indicator lamp of

the generator will glow 12.

Turn the variable steam control knob to the middle 13.

Wait till the appliance is ready for operation (when it is ready, an audio signal

is sounded) 14.

Lift the iron and hold it in the air and press the steam trigger till steam starts

to come out. When the appliance is used for the first time, this takes up to 30

seconds 15.

As long as the yellow steam generator indicator lamp glows 12 (about 2

min.), the steam output quantity remains at a reduced level. When the indica-

tor lamp goes off, it automatically increases.

3.8 Switching On and Heating Up

Phase

11 12

13 14

During ironing, the yellow steam generation indicator lamp

and the red heating-up lamp of the iron go on and off regu-

larly: This indicates that the generator and iron are getting

heated. This is a normal feature.

The flow control knob can be used to adjust the quantity of steam continu-

ously depending on the material (also see the table on page 9).

Continuous variable steam output 16:

Adjust the flow control knob to suit the type of material being ironed, to the

desired position. The table on page 9 shows typical applications. The more

you rotate the knob clockwise"+", the greater does the quantity of steam

output become.

"E" = Eco-Mode 17 (only model VX 250):

This setting is recommended for quick ironing jobs that need less steam (for

example, when you want to straighten out a slightly creased blouse early in

the morning).

"Maxi"-Modus / Turbo steam 18 (only model VX 250):

In this position, lots of steam comes out of the base of the iron for a few

seconds (= "Turbo-steam"); thereafter, the steam output quantity is reduced

back to the normal level.

Wait for a few seconds before you repeat this turbo-effect, since otherwise,

water can come out of the base (the steam has to get heated up again first).

Press the steam trigger to get steam 19.

Here are a few valuable tips for using the appliance:

Owing to the high steam output, press the steam trigger only briefly

only once. Brief and repeated pressing of the steam trigger is enough to

continuously get an adequate quantity of steam (pressing it for too long can

result in water being ejected).

When use is intensive, steam can come out even after releasing the

steam trigger. Therefore, the residual steam can condense on the ironing rest

and water residue is left behind. This is normal. Sponge it off if necessary.

There is no risk of the metal being damaged.

Turn the flow control knob to the middle 17:

- the appliance is used for the first time,

- if the water tank is empty,

- every time the anti-scale cartridge is replaced.

3.9 Variable steam control knob

3.10 Generating steam/Steam trigger

Caution! If there is no more water in the tank do not press

the steam trigger any more!

3.7 Connecting

Caution! Electrical energy can be fatal! In an emer-

gency, immediately pull the plug from the socket. Never

allow live parts to come in contact with water!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Turmix VX 250 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info