Bedienungsanleitung Tusa RS-860 (Seite 25 von 96) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

557349

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

- 24 -

Regulators

17 18

Regulators

diving, thus reducing the load on the face during use. The main body materials are

super-tough nylon (heat pliable polyamide resin) reinforced with glass fiber for out-

standing hardness and shock resistance. The materials also offer superior tensile

strength, dimensional stability, heat resistance, weather resistance and chemical resis-

tance.

Intake resistance

* The second stage includes a director to forcibly guide air from the demand valve. That

prevents free flow while significantly lessening intake resistance.The result is one of the

lightest intake resistance values in the industry compared with products from other

companies.

New mouthpiece

The new mouthpiece, developed on the basis of ergonomic engineering, further

enhances the comfort of bite, fit, and stability. Even with a light bite, a high level of sta-

bility is achieved, so there is no fatigue from long periods of usage.

Venturi Adjustment Lever (RS-680, SS-80)

The addition of a venturi adjustment lever on the S-80 allows the regulator to power

assist the diver when underwater utilizing the natural venture effect. The diver can also

adjust the lever to prevent free flow such as on a surface swim.

Swivel joint (RS-350, 340, 654, 680, 670)

For optimum performance and comfort, a swivel joint is fitted between the second stage

and the joint section of the low pressure hose. The swivel joint allows flexibility of the

hose for eliminate hose tension at the mouthpiece for a more natural and comfortable

bite.

“Air Refresher” filter (RS-350)

There are two types of high tech filter built into the second stage. An active carbon filter

cleans the air and absorbs smells, while a metal fiber filer eliminates particles as small

as 100 microns.This makes sure that the cleanest and safest air is supplied to the diver.

S.E.A. -Sequential Exhaust Assist [PAT.P.] (RS-680)

The Sequential Exhaust Assist (S.E.A.) is an auxiliary exhaust valve, located on top

of the S-80 elliptical case to decrease primal exhaustion resistance.

SECTION III

PRE-DIVE PROCEDURES

WARNING

Do not attempt to connect low pressure hoses to the high pressure ports with the use

of an adapter. Improper connection will cause damage to the equipment and could

result in serious personal injury. Low pressure components are not intended to

withstand

pressures greater than 28Bar

≒

(400 PSI). When installing your accessory

hoses, avoid damaging the O-ring. Tighten gently, but firmly into the first stage housing.

SCUBA complying with EN 250 are not intended for more than one user to breathe from

at the same time.

If SCUBA are configured and used by more than one diver at the same time, then the

cold water and breathing performances may not fulfil the requirements of EN 250.

RS-350, 340

Always connect the Octopus Regulator to the portmarked with SS. Connecting to any

other port is strictly prohibited.

PRE-DIVE OPERATING INSTRUCTIONS

1. Position the tank valve so the outlet points toward the diver.

2. Remove the dust cap from the first stage inlet and place the yoke (or DIN adaptor)

in the center of the cylinder valve connection.

3. Position the first stage body so that the second stage hose goes over the right

shoulder of the diver.

4. Hand-tighten the yoke screw or DIN adoptorscrew.

5. Check all the hose connections to the first and second stages. If they can be

loosened by hand, they should be tightened with a wrench before pressurizing.

6. Check the submersible pressure gauge to make sure it indicates zero pressure.

7. Open the tank valve slowly to gradually allow air into the regulator.

NOTE: During this operation, depress the second stage purge button to reduce

shock to the valve mechanism. Do not perform this operation in a cold environment

below 10°C (50°F). Performing this in a cold environment may cause “freeze-up” of

the regulator which can render it inoperable. If this occurs, you should contact a

TUSA authorized service center.

8. Check the submersible pressure gauge to ensure that it indicates the proper tank

pressure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tusa RS-860 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info