Bedienungsanleitung U.N.O. TR 4.0 (Seite 34 von 39) (Englisch)

765111

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

CALIBRATION PROCEDURE

1. Remove the safety key

2. Press and hold down the Start and Fast

+ buttons and replace the safety key.

Continue to hold the

Start and

Fast key until the window displays “Factory settings press

enter”, then press the

Enter key.

3. You will now be able to set the display to show Metric or English settings (Miles vs. Kilometers).

To do this, press the up or down key to show which you want, then press

Enter.

4. Make sure the wheel size diameter is 3.01 then press

Enter

5. Adjust the minimum speed (if needed) to 0.5 mph /1.0 kmph and then press

Enter

6. Adjust the maximum speed (if needed) to 12.0 mph / 18.0 kmph and then press

Enter

7. Adjust the maximum elevation (if needed) to 15 and then press

Enter

8. Grade return – On (This allows the incline to return to zero when

Stop is pressed on training)

9. Press

Start to begin calibration. The process is automatic; the speed will start up

without warning, so do not stand on the belt.

ADJUSTING THE SPEED SENSOR

If the calibration does not pass you may need to check the speed sensor alignment.

1. Remove the motor cover hood by loosening the 4 screws that hold it in

place (you do not need to remove them completely).

2. The speed sensor is located on the left side of the frame, right next to the

front roller pulley (the pulley will have a belt around it that also goes to the

motor). The speed sensor is small and black with a wire connected to it.

3. Make sure the sensor is as close as possible to the pulley without

touching it. You will see a magnet on the face of the pulley; make sure

the sensor is aligned with the magnet. There is a screw that holds the

sensor in place that needs to be loosened to adjust the sensor.

Re-tighten the screw when finished.

MAINTENANCE MENU

1. Press and hold the

Start, Stop and

Enter key at the same time, until the display shows “Engineering

mode” (it may say maintenance menu, depending on version). Press the

Enter key.

2. You can now scroll through the menu using the + and - keys. Use the

Stop key to return to previous

menu selection. The menu selections are:

A. Key Test - Tests that each key is functioning properly

B. Display test - Test the LCD display segments are all lighting properly

C. Functions

I. Sleep Mode - Allows you to turn off the sleep mode. Console will stay on all the time unless

power is turned off.

II. Pause Mode - When the console is paused during a program this will allow you to keep the

console paused indefinitely instead of 5 minutes.

III. Odometer reset- Allows you to reset the odometer

IV. Unit Metric- When enter is pressed allows you to change the settings for data to metric.

V. Motor Test - For service personnel only when troubleshooting motor problems.

VI. Beep - Allows you to disable the speaker so there is no beeping.

VII. Grade return - When in Pause mode the incline will return to zero automatically.

D. Security - Allows you to lock the keypad so the treadmill cannot be used. Press Enter to change

setting (also called child lock).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

U.N.O. TR 4.0 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von U.N.O. TR 4.0

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info