Bedienungsanleitung Ulma 40 Kw (Seite 3 von 34) (Englisch)

694450

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

⁭ Information

• Keep this manual so that it is accessible to professionals and future needs.

• Read this manual carefully before putting the pellet burner into service.

• Follow the manual and its instructions carefully and do recommended management and maintenance.

Registration to the local building authority in your municipality

N.B.: At every change of heating system, the local building authority of the municipality has to be contacted

and a so called “Construction Registration” is made.

Inspection

Heating plants installed today shall be inspected and approved by authorized inspector like the local certified

chimney-sweeper. The local building authority in the municipality can inform you how this could work.

Important at installation

• Run the feed auger of the burner by itself until the pellets start to come in constant flow. This can be made

by connecting the feed cable of the burner directly to the cable of the auger. Run the auger approx. 15min

after the first pellets have reached the outlet on the auger.

• The auger shall have a max angle 45 degrees and not be below 43 degrees.

• We recommend that the length of the hose, between the burner and the auger, should not be below

500mm. The auger shall also be placed so that it sits a little to the side of the tipping chute of the burner,

this to avoid that pellets can fall down into the burner if back burning would occur when the hose burns off

as a part of the safety.

• Hose inclination must be more than 45 degrees, otherwise the pellets are stuck in the hose.

• At adjustment of the burner, the draft limiter should be adjusted after the draft conditions of the chimney.

• The feed cable of the burner shall be connected above the overheating protection of the boiler.

Sweeping

Chimney sweeping shall in accordance with the fire-protection law shall be made frequently during the year.

This is made by your local chimney sweeper. Regular cleaning of heating surface of the boiler shall be made

in a way so that good operating economy is obtained. Prepare sweeping by turning off the boiler at least a

couple of hours before cleaning to minimize the amount of glowing ash.

Warning!

See to that the power to the boiler is turned off before the cover over the burner is removed and dismount

cabling to the burner when the burner is removed from the boiler.

Maintenance agreement increases operation length and life of the burner

ULMA AB recommends subscription of annual maintenance agreement.

For more information contact your local ULMA retailer.

Change of wear parts

ULMA AB always recommends that wear parts, when needed, are being changed by an authorized service

technician at your ULMA retailer. Ulma’s retailers can provide necessary spare parts and at change make

sure that the parts being changed on the unit go through alignment and that a flue-gas analysis of the unit is

made.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ulma 40 Kw Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ulma 40 Kw

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info