Bedienungsanleitung Ultimate speed ULGD 3.8 A1 - IAN 102626 (Seite 7 von 59) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Schwedisch, Finnisch)

576656

Zoom out

Zoom in

Vorherige Seite

1/59

Nächste Seite

ULGD 3.8 A1

Operation

Before use

♦ Before connecting the charger, the operating

instructions must be observed.

♦ Furthermore, the instructions of the vehicle man-

ufacturer regar

ding a permanently connected

vehicle battery must be observed. Secure the

vehicle, switch oﬀ the ignition.

♦ Clean the battery poles. Take care that while

doing so, your ey

es do not come into contact

with the dirt.

♦ Ensure suﬃ cient ventilation.

Connecting

♦ Before starting the charging or trickle charging

procedure on a permanently installed battery in

a vehicle, ﬁ rst disconnect the negative terminal

connecting cable (black) of the vehicle from the

negative terminal of the battery. The negative

terminal of the battery is usually connected to

the vehicle’s coachwork.

♦ Connect the positive pole clamp (red)

of the

charger to the positive pole of the battery.

♦ Connect the negative pole clamp (black)

to the

negative pole of the battery.

♦ Connect the mains cable

of the charger to

the mains socket.

♦ The battery voltage display

shows the cur-

rent battery voltage.

♦ Should the connection of the clamps be

swapped, the LED „re

verse connection“

lights up.

Disconnect

♦ Disconnect the appliance from the mains supply.

♦ Remove the negative pole clamp (black)

from

the negative pole of the battery.

♦ Remove the positive pole clamp (red)

from

the positive pole of the battery.

Measuring STANDBY /

Battery voltage

After connection to the grid, the appliance is on

STANDBY. The standby display lights up. When

the clamps are connected, the battery voltage is

shown in the LCD (voltage display

). The segments

of the condition display are empty.

If the voltage is below 3.8 V or above 15 V, the

battery will not be charged. The display brieﬂ y

shows the error message „Err“.

The appliance goes on standby.

6 V battery:

If the voltage range of the battery is measured

as between 3.7–7.3 V, only program 1 can be

selected.

12 V batteries:

If a battery is recognised in the critical voltage

range of between 7.3–10.5 V, the appliance

checks whether a fully charged 6 V battery, or a

discharged 12 V battery is present. After pressing

the program selection button

to select a program,

the appliance carries out a control measurement

for about 90 sec.

The display shows:

If after about 90 sec. between 7.3–7.5 V are

detected, the 12 V battery is defective.

The appliance goes on standby.

Revitalising

If after about 90 sec. between 7.5–10.5 V are

detected, a 12 V battery is present.

Charging starts with a pulse charge for revitalis-

ing. The voltage display

ﬂ ashes. Once 10.5 V

are reached, the appliance switches to the other

charge steps.

Revitalising is the same for all the 12 V charge

programmes.

IB_102626_ULGD3.8A1_FI_SE_DK_BE_NL.indb 4 06.08.14 08:48

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ultimate speed ULGD 3.8 A1 - IAN 102626 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info