Bedienungsanleitung Ultimate speed ULGD 3.8 A1 - IAN 270075 (Seite 8 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Schwedisch, Finnisch)

647785

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ULGD 3.8 A1

Measuring STANDBY /

Battery voltage

After connection to the grid, the appliance is on

STANDBY. The standby display lights up. When

the clamps are connected, the battery voltage is

shown in the LCD (voltage display

). The segments

of the condition display

are empty.

If the voltage is below 3.8 V or above 15 V, the

battery will not be charged. The display brieﬂy

shows the error message „Err“.

The appliance goes on standby.

6 V battery:

If the voltage range of the battery is measured

as between 3.7–7.3 V, only program 1 can be

selected.

12 V batteries:

If a battery is recognised in the critical voltage

range of between 7.3–10.5 V, the appliance

checks whether a fully charged 6 V battery, or a

discharged 12 V battery is present. After pressing

the program selection button

to select a program,

the appliance carries out a control measurement

for about 90 sec.

The display shows:

If after about 90 sec. between 7.3–7.5 V are

detected, the 12 V battery is defective.

The appliance goes on standby.

Revitalising

If after about 90 sec. between 7.5–10.5 V are

detected, a 12 V battery is present.

Charging starts with a pulse charge for revitalis-

ing. The voltage display ﬂashes. Once 10.5 V

are reached, the appliance switches to the other

charge steps.

Revitalising is the same for all the 12 V charge

programmes.

Program selection

NOTES

► If a battery is detected in the voltage range of

between 3.7–7.3 V, the programmes 2–3–4

can not be selected. The charging process takes

place automatically. Depending on the selected

program, the characteristic charge curve is

monitored for voltage, time and temperature.

Included are the diagnostics program, revitalis-

ing mode and retention charge.

(See principle representation program 3 Fig. C)

Program max. (V) max. (A)

1 6 V 7,3 V 0,8 A

14,4 V 0,8 A

14,4 V 3,8 A

14,7 V 3,8 A

Program 1 „6 V“ (7,3 V / 0,8 A)

For charging 6 V batteries with a capacity of less

than 14 Ah.

♦ Press the program selection button

, to select

program 1. The symbol „6 V“ is displayed on

the LCD. During charging, the charge display

ﬂashes and shows the progress of the charge

procedure (1–4 bars). When the battery is fully

charged, the condition display shows 4 bars.

The ﬂashing stops and the appliance automati-

cally switches to retention charge.

Program 2 „12 V“ (14,4 V / 0,8 A)

For charging 12 V batteries with a capacity of less

than 14 Ah.

♦ Press the program selection button

, to select

program 2. The symbol is displayed on the

LCD. During charging, the charge display

ﬂashes and shows the progress of the charge

procedure (1–4 bars). When the battery is fully

charged, the condition display

shows 4 bars.

The ﬂashing stops and the appliance automati-

cally switches to retention charge.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ultimate speed ULGD 3.8 A1 - IAN 270075 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info