Bedienungsanleitung Ultimate speed UMK 10 C2 - IAN 298835 (Seite 9 von 43) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

763016

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

9 GB/IE/NI

Initial use

Place the product on a level, non-ﬂammable

surface. Do not cover the vents. Do not operate

the device in dusty environments. Doing so poses

a ﬁre hazard and could damage the device.

For inﬂatables with counterpressure (e.g. partly

ﬁlled car tyre): Switch on the product before

connecting the connection valve 7 to the tyre.

Note: Depending on the inﬂatable you can

use the connection valve 7 directly or along

with the included valve adapter 10 (see Fig. A).

Connecting to the cigarette lighter socket:

Note: Verify the socket of the cigarette lighter in

your vehicle has an adequately sized fuse.

Verify the product is switched oﬀ: on / oﬀ

switch 6 to position “0“.

Plug the cigarette lighter plug 5 into the socket

of the 12 V cigarette lighter.

Connecting the connection valve 7:

Open the connection valve 7: clamping

lever 8 vertical (see Fig. B).

Connecting without valve adapter 10 :

- Insert the open connection valve 7 into the

valve of the inﬂatable (if necessary, ﬁrst remove

valve cover of the inﬂatable).

- Hold the connection valve and close: push

tensioning lever

toward connection valve

Connecting with valve adapter 10 :

- Push the respective valve adapter into the

opening in the connection valve 7.

- Secure the valve adapter into the connection

valve 7: push clamping lever 8 toward

connection valve (see Fig. C).

- Insert the valve adapter 10 into the valve on

the inﬂatable (if necessary, ﬁrst remove valve

cover of the inﬂatable).

Switching on / off:

Switch the device on: on / oﬀ switch 6 to

position “I“.

Once the desired ﬁlling pressure has been

reached, switch the device oﬀ: on / oﬀ

switch 6 to position “0“.

Remove the cigarette lighter plug 5.

Removing the connetion valve:

Connecting without valve adapter 10 : Open

the clamping lever 8 for the connection

valve 7 and remove from the valve of the

inﬂatable.

Connecting with valve adapter 10 : Remove the

valve adapter from the valve of the inﬂatable.

Open the clamping lever 8 of the connection

valve 7 and remove the valve adapter 10 .

Note: Air may escape from the valve of the inﬂat-

able when removing the connection valve 7. Be

sure not to remove the connection valve 7 too

quickly.

The manometer 2 is not calibrated. Therefore

seek a specialist facility with a calibrated de-

vice after inﬂating inﬂatables where incorrect

pressure can be dangerous (e.g. car tyre).

Operation

Working instructions

This product is not suitable for continuous operation.

It was developed to produce air pressure, not air

volume.

Do not use the product for longer than 5 minutes

without interruption to prevent overheating and

damage to the device. Afterwards allow to

cool for a minimum of 20 minutes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ultimate speed UMK 10 C2 - IAN 298835 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ultimate speed UMK 10 C2 - IAN 298835

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info