Bedienungsanleitung Uniden UBC 100XLT (Seite 8 von 11) (Englisch)

647639

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

, ' "

,','" ,.,.,.;- :-":.':"; :,=..; ::.,:':;, , " ,'" .",

,', .'qp~[~Ji9g',': .. "",'

.:.

The U8C IOOXLThas 100 memorychanne/s. each of which can be programmed to

store one Frequency. The channels are divided inro 10-10 channel banks. useful

Forstoring similar Frequencies in order to maintain Faster scanning cycles. When

scan is pressed. each of the programmed Frequencies withIn a selected bank will

be sampled Fora transmission (locked channels will be skipped) at the rate of

about 15 channels per second. Ifan active Frequency is found the unitwill stop and

monitor that Frequency until there is no longer any activity. A two second delay

can be added ro each channel and will allow the unit to monitor the Frequency for

a return or continued transmission. If. after two seconds. the Frequency remains

inactive. the scanning cycle will resume.

When the unit is first turned on. each channel WIllcontain ~OOO.OOO*.When new

Frequencies are programmed. the old will be erased. If an invalid Frequenoj is

entered. ~Error" will be displayed and the old Frequency WIll return.

To operate the scanner make sure that the batterIes are charged or power is

correctly conneaed to the unit. Turn the volume control on and adjust the cesired

level. Adjust the squelch by tUrning the knob Fullyclockwise untIl a rushIng sound

is heard. Turn the knob back until the receIver is silent. After the channels have

been programmed. operation is simple. Press the scan key to scan all the channels.

While the receIver ISscannIng channels. pressing one of the number keys will tUrn

a bank of 10 channels on or off. The black lines at the top of the LCO display show

you whIch banks are seleaed. Ifa bank is already selec:ed, (shown by a black line

under the bank number) pressing the corresponding burron will dese!ea that

bank. Press the manual key to stop scannIng. ,~epeateQly pressing the manual key

wIll step through the channels in order.

LCD Display

The U8C 1OOXlT has a backJit display whIch shows the current channel and

frequenCj as well as other operatIonal modes. When (he unIt is scanning. the

channel number wIll rapIdly advance while the frequenOj display wIll go blank.

When the scanner IS stopped the current channel and frequenoj will again be

displayed.

When frequencies are programmed the display WIll show the digitS as they are

entered. The display will also show *PRI* when the priorIty mode is on, ~l/O*

whenever a channel appears that has been locked our. and ~DLY"whenever a

channel has been programmed for delay, Across the tap of the display. a serIes of

dashes under the numbers 1-) 0 will be present. These are the bank indicator

numbers. These are se!eaed or deseleaed durIng the scan sequence by the use of

the numerIC pad.

'- -,-_.,- ... ""'-"---'--' -- ~- --- -- ..., .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Uniden UBC 100XLT Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info