Bedienungsanleitung Unold 28811 (Seite 31 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

111427

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Reinsert the coffee outlet into the support on the appliance.26.

Cleaning the steam nozzle

Carefully detach the nozzle from the frother.27.

Carefully clean the nozzle with warm water and a mild 28.

washing-up liquid. Rinse the nozzle with clear water and dry

it thoroughly.

Reattach the steam nozzle on the frother.29.

Detaching the brewer assembly

The automatic coffee machine has a detachable brewer 30.

assembly, which is important for the coffee quality and the

operational reliability of the appliance. Clean the brewer

assembly regularly, if necessary daily.

Open the lateral cover. Always detach the coffee grounds 31.

container first, then the brewer assembly, holding them on

the handle and pressing the plate with the label PRESS

downwards and extracting the brewer assembly.

If it is not possible to extract the brewer assembly, the water 32.

drain pipe might be trapped. The water drain pipe is installed

in the upper left of the brewer assembly. Carefully pull on the

drain pipe until the brewer assembly can be detached. After

cleaning the gasket of the water drain pipe, grease it with a

silicone lubricant.

Rinse the brewer assembly with water. Do not clean the 33.

brewer assembly in a dish-washer. To clean all components

of the brewer assembly, insert the brewer assembly key into

the round hole on the rear of the brewer assembly and turn it.

Rinse the brewer assembly with water.

Clean the perforated screens of the brewer assembly with 34.

a soft brush, if necessary. The perforated screens can be

detached using the brewer assembly key.

Do not use cleaning agents or disinfectants to clean the brewer 35.

assembly. Dry the brewer assembly with a soft cloth.

Grease the lateral guides as well as the red gasket of the 36.

brewer assembly every once in a while with the silicone grease

enclosed. The red gasket should be replaced once a year or

according to its wear.

Also grease the water inlet port of the brewer assembly.37.

To better distribute the grease, actuate the brewer assembly 38.

several times using the brewer assembly key. Reinsert the

brewer assembly into the automatic coffee machine.

Extract, empty and clean the coffee powder drawer beneath 39.

the brewer assembly.

Clean the inside of the automatic coffee machine with a dry 40.

cloth or a cleaning brush.

Then put the brewer assembly back to its initial position. The 41.

brewer has two arrow marks on the front beneath the handle.

These must point at one another to allow the insertion of the

brewer assembly.

First reinsert the brewer assembly until it latches into place, 42.

then reinsert the coffee grounds container.

Should the brewer assembly be trapped, thus making its 43.

extraction or reinsertion impossible, the appliance has to be

inspected and repaired by our after-sales service

All components of the automatic coffee machine have to be 44.

dry before reinserting them and using the appliance.

Never clean the brewer assembly with a cleaning agent or disinfec-

tant.

Never dry the brewer assembly or other components with a hair dryer

or other electric drying appliances or in the oven/microwave.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Unold 28811 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info