Bedienungsanleitung Unox LineMiss (Seite 7 von 72) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

554531

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

UNO

parameters: TIME and TEMPERATURE.

TIME set up

To set the time of functioning, it is sufficient to

operate on the + and – keys (time can be set from 0

hours and 01 minute to 9 hours and 59 minutes)

When you read INF on the TIME display, the oven

will work continuously until you stop it pressing the

START/STOP key.

TEMPERATURE set up

To set the temperature desired inside the cavity

it is sufficient to operate on the + and – keys

(temperature can be set from 0 to 260°C – starting

temperature 30°C)

Start / Stop cooking cycle

It is possibile to start the cooking cycle pressing the

START / STOP key (the related LED will switch on).

It is possibile to stop the cooking cycle pressing the

START / STOP key.

At the end of a cooking cycle the heating elements

and motors will be switched off, the buzzer will ring

for 15 seconds, the digits 0.00 will flash for 45

seconds on the display, the set temperature remains

the one entered at the beginning of the cooking

cycle and the START/STOP LED will remain turned

on.

If during the 45 seconds of flashing digits (0.00) the

operator set a time (using the + or – keys), the oven

automatically starts functioning.

At the end of the 45 seconds or if the cooking cycle

is interrupted by pressing the START / STOP keys,

all the parameters previously set will turn into 0 (the

operator will be in the same situation there is when

the oven has just been turned on) and the START/

STOP LED will be switched off.

Visualization and modification of the

cooking parameters during the functioning

of the oven

While the oven is working, it is possibile to visualize

the parameters and modify them if the oven is

working in the manual mode; to scroll the different

parameters (time, temperature) you have to push

the SELECT key.

If you select time, the display visualizes the remaining

time (COUNTDOWN related to the selected step).

If you select temperature, the display alternately

visualizes for 4 seconds the set tempeture (fixed LED

– it is possibile to modify the temperature using +

or – keys) and the measured temperature (flashing

LED).

PROGRAMMED MODE

There are 70 programs available.

Memorization of a new program

To memorize a cooking program it is necessary to

proceed as follows:

- enter the programming mode pushing the P

key: on the display you will read the writing

P01

- select the number of program you desire by

using the + or - keys (the program number

will show on the display)

- press the SELECT key

- set the cooking parameters as explained in

the manual mode

- save the program by pressing the MEM key

for 5 seconds; the storage of the program

will be confirmed by the sound of the buzzer

and by the visualization of the chosen

program number on the display

- press the P key to go back to the manual

mode.

Recall of a memorized program

To recall a memorized program it is necessary to

proceed as follows:

- enter the programming mode pushing the P

key: on the display you will read the writing

P01

- select the number of program you desire by

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Unox LineMiss Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Unox LineMiss

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info