Bedienungsanleitung Unox SpidoCook (Seite 16 von 22) (Englisch)

554537

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

B D3D1 D2

SpidoTouch digital control operation

Control Panel:

Powerswitch(A)

Activates the unit.

Buttonlocatedoutside:contactgrillo

Buttonlocatedinside:contactgrillon

SpidoTouch digital control(B)

Allows you to set the cooking time and tem-

perature and store up to 4 programmes.

Temperaturelight(C)

Light on: Heat is on.

Light o: Set temperature reached

Time and cooking temperature parameter setting

temperature

 (max.300°C)

Time

0 = STOP (grill OFF)

00:01....9:59 (maximum time)

INF= innite operation (plate always on)

• Setthecookingdurationbyrepeatedlypushing(slowmode)orholdingdown(fastmode)the

button

untilthedesiredtimeappearsonthescreen(thevaluehasbeensavedwhentheLED(D1)stopsashing).

• The countdown starts right after having set the duration with a value other than “0”, and the plate will start

to heat until reaching the pre-set temperature of 200°C. To change this value, push the button until the

desiredtemperatureappearsonthescreen(thevaluehasbeensavedwhentheLED(D2)stopsashing).

NOTE: if you press the buttonbeforethedurationLED(D1)hasstoppedashing,theplatewillheatuntil

it reaches a temperature of approximately 200°C.

• To prematurely stop cooking, repeatedly press the button until 00:00 appears on the screen.

• Example:Ifyouwanttocookatatemperatureof220°Cfor5minutesand30seconds.

Turn on the plate with the button (A), hold down the button until 5.30 (5 minutes and 30 seconds) appears on

the screen. After a few seconds, the LED (D1) stops ashing: the cooking time has been saved, the countdown starts

and the plate starts to heat to the pre-set temperature of 200°C.

To increase the temperature, hold down the button until the temperature of 220°C appears on the screen.

After a few seconds, the LED (D2) stops ashing: the cooking temperature has been saved.

When the pilot light (C) turns o, the plate has reached the set temperature (220°C).

Program storage and use

Up to fourprogrammes(P1, P2, P3 andP4) can be saved for subsequent use.

PROGRAM STORAGE

Set the time and temperature parameters as describe previously (example 8 min. / 220°C).

To store the program press and hold the button P1, P2, P3 or P4 (ex. P3) for at least 3 seconds: the conrmation

ofrecordingtakesplacewiththelightonforonesecondoftheLEDlight(D3)andthebuzzer.

E.g.: Programme P3 = the plate will work at 220°C for 8 minutes

english

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Unox SpidoCook Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Unox SpidoCook

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info