Bedienungsanleitung Unox XF103 (Seite 4 von 72) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

636397

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

UNO

Carefully remove all the protective film from the

external walls of the appliance. Pay attention not to

leave any rest of glue on the sides.

If there should be any residue, please remove it with

an appropriate solvent.

4. INSTALLATION

4.1 – ELECTRICAL CONNECTION

4.2 – WATER CONNECTION

4.1 ELECTRICAL CONNECTION

a- The connection to the electrical power

supply system must be done by qualified

personnel according to the standard in

force. The installer is responsable for a

correct electrical connection and for security

rules observance.

Before connecting the appliance, make

yourself sure that the voltage and the

frequency correspond to those stated on the

data plate of the appliance. The appliance

must be placed so that the connection plug

to the network can be easily reached.

Place an omni-polar switch between the

appliance and the network. The switch

must be easily accessible after installation.

The contacts of this switch must have a

minimum opening distance of 3 mm and

the switch must have an appropriate input.

It is suggested to use a differential magneto-

thermal switch.

When the appliance is working, the power

supply voltage must not diverge from the

value of the nominal voltage, written on the

technical data plate, by more than ± 10%.

b- The appliance must be connected to the

ground line of the network.

Moreover, the appliance must be included in

an equipotential system whose

efficiency must be properly

checked according to the

current law. This connection

must be done between the

different appliances using

the terminal marked with the

symbol:

The equipotential conductor must have a minimum

section of 10 mm2.

POWER SUPPLY CONNECTION

1- Ovens equipped with cordset and Schuko

plug (single phase 230V): is sufficient

to insert the plug in the proper socket

(the socket must be suitable for the plug

assembled in the oven)

2- Ovens equipped with cordset (three phases

400V + Neutral): these ovens are equipped

with electrical cord with 5 conductors: it

is necessary to connect the proper three-

phase 5 poles plugi with suitable capacity

or you can connect the cord directly to the

electrical panel.

In those ovens equipped with a cord with 5 conductors

it is possible to substitute the power cord to adapt

the appliance to the available type of current.

Replacement of electric supply cable (in case of

damage or change of electric connection) has to be

done by authorized technical assistance service or

anyway by someone with similar qualification.

To substitute the power cord proceed as follows:

- Open the cover of the terminal board

levering the two lateral small wings with a

proper screw-driver (1)

- Unscrew the screws that lock the conductors

(2)

- Unscrew the screw that locks the cordstopper

(3)

- Remove the supplied cord

- Connect the conductors that you would like

to use according to the chosen connection

drawing; be sure to fix properly the screws of

the clamps.

- Block the cord using the proper

cordstopper

- Close the cover of the terminal board.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Unox XF103 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info