Bedienungsanleitung UPM THM301M (Seite 7 von 8) (Englisch)

581336

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

- AA SIZE +

System Type

Gas - Standing Pilot

Gas - Electronic Ignition

Gas - Fire Boiler

Gas - Millivolt System

Oil - Fire Boilers

Oil - Fire Furnace

Electric Furnace

Electric Air Conditioner

Baseboard Electric Heater (120/240V)

Heat Pump/Multi- Stage equipment

Compatibility

Generally, equipment with low voltage control is compatible with the THM301M thermostat. For

details on compatibility of your particular equipment, please call our technical assistance line.

continuously to improve air ventilation. To return to automatic control, set the switch to the AUTO

position.

Heat/Cool Control Switch

! If this switch is on the OFF position, both the heating and cooling systems are turned off, and all

programs and settings will be disabled.

! Slide the switch to HEAT or COOL to control the heating or air-conditioning system.

! The symbols HEAT or COOL on the display will be flashing when heating or cooling is activated.

Pre-Comfort Recovery

This thermostat is equipped with a ‘Pre-Comfort Recovery’ system that will activate the heating or

cooling in advance of the actual set program time so that the room will be at the desired temperature

at the start of the comfort program time.

It is normal for the system to be activated earlier (up to ½ hour for heating and one hour for cooling)

than the actual set program time.

12/24 Hour Display Format

Press both AHEAD and BACK keys together at the same time to change the time display from 12

hour format to 24 hour format (e.g. 8:00pm / 20:00) and vice versa.

Changing Batteries

When all digits on the LCD display flashes, it indicates that the batteries are running low and have to

be replaced. However, it is recommended for the batteries to be replaced every year even if display is

not flashing yet. To replace batteries:

! Set the thermostat system switch to the OFF position and have the new batteries on-hand.

! Open the thermostat by pressing on the 2 tabs on the top.

! Remove the old batteries and install new ones quickly.

! Close the thermostat to its original position.

If new batteries are inserted within 20 seconds of removing the old ones, the existing time and

programs will not be cleared. Otherwise, the display will show 9:00a.m. and the thermostat will have

to be re-programmed.

Installation

The following tools may be required for installation:

See below to select a suitable place for the new thermostat installation. And refer to "Replacing Old

Thermostat" section to replace old thermostat.

Compatible with THM301M

Yes

Some models

Two AA size batteries (included)

Wire Stripper/Cutter

(If necessary, to strip the wires)

Level

(If necessary, to level the thermostat)

Masking Tape

(To wrap the exposed wires temporarily and labeling

the disconnected wires)

Hand Power Drill with a 3/16 inch bit

( If necessary, to drill holes on the wall )

Cross (Phillips) screwdriver

Yes

* Not compatible with any 120/240 volt circuit

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

UPM THM301M Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von UPM THM301M

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info