BUTTON PLACEMENT
1
6
7
8
9
2
3
4
5
MIN/-/MIN: shows minimum temperature;
adjusts clock, alarm, and temperature alarm
values
C/F: changes House Code and Channel Code;
selects °C or °F
SET activates SET function
Battery Compartment
LCD Screen
ALARM /(°C/°F): toggles between °C and °F
12 and 24 hour format, and alarm ON and OFF;
disables temperature alarms
CHN: scrolls through local and remote
channels (1 to 4);
HOUR/+/MAX: shows maximum temperature;
adjusts clock, alarm, and temperature alarm
values
MODE/SNOOZE: scrolls through the
clock, alarm, and (upper & lower) temperature
alarm modes; snooze for alarm
GETTING STARTED
Remove battery cover
Set up the transmitter(s) setting up the receiverbefore
Remove battery cover
2 AA size batteries (included)
2 AA size batteries (included)
setting up the transmitter
1
*
1
The temperature will appear on the LCD screen
House code will blink for 8 seconds
2
2
3
3
4
5
6
7
8
9
10
Select House code (1-15) by pressing C/F
Press SET
Press SET
Channel code will blink for 8 seconds
Select Channel code (1-4) by pressing C/F
* If you have multiple transmitters for a single receiver
set each transmitter to the House codesame
* If you have multiple transmitters for a single receiver
set each transmitter to a Channel codedifferent
Min and Max T
T
WS222 Receiver
WT440 Remote T
TEMPERA
A
B
*
The trend indicator shows the trend of the temperature
in the past half-hour interval.
Example:
The following indicates that the
temperature is rising.
Arrow Indicator
Rising
Steady
Falling
T
WS222 + WT440
Wireless Weather Station
OWNER’S
MANUAL
setting up the receiver
Synchronized!!!
1
1
1
2
2
3
4
WIRELESS TRANSMIS
Automatic Learn Function:
Manual Learn Function (Remote Signal Search):
The learn function starts automatically and runs for approximately
3 minutes when batteries are first installed in the receiver
Press and hold for
3 seconds to start.
CHN
If a new remote transmitter is added or if signal is lost (outdoor readout
on the receiver is blinking), the learn function must be executed again.
Within the 3 minutes, the receiver will pick up the temperature
signal from the remote transmitter and display the reading.
Unit will beep to indicate that
learn function has started.
Channel symbol will blink and
unit will continue to beep as
each remote transmitter is detected.
1
Within 3 minutes, the temperature reading of the remote transmitter
will display on the receiver
WS222 receiver
WT440 transmitter
10
Battery Cover
11
Wall Mount Bracket & T
1
1
SET
C/F
-
AA
1
.5V
+
-
AA
1
.5V
+
5
9
4
7
6
8
10
11
2
Insert batteries into compartment,
observing proper polarity
Insert batteries into compartment,
observing proper polarity; replace cover
Select temperature display in C or F by pressing C/F
°°
Replace battery cover
Congratulations on your purchase of this
weather station set, WS222+WT440.
Please take the time to read and
understand this manual so you can begin
to enjoy the convenience and features this
product has to offer
Main Display Unit WS222:
* clock and alarm clock function
* local temperature display
* receives and displays temperature
readings from up to 4 remote
transmitters via RF technology of 433MHz
* minimum/maximum temperature memory
* temperature trend indicator
* local/remote temperature alarms
* day/night icon
* user-selectable C or F
* battery type:2xA
°°
FEA
Remote T
* drip-proof design with LCD screen
* temperature display in user-selectable
Co F
* transmission range: up to 40 metres in
open area
* table stand or wall mountable
* battery type:2xA
°°
SET
C/F
-
AA
1
.5V
+
-
AA
1
.5V
+
11
10
2
11
12
3
1
12
1
1
1
8
9
6
7
P i
the minimum temperature
The MIN symbol will appear
MIN
.
T return to normal temperature
display press again.MIN
T return to normal temperature
display press again.MAX
P i
the maximum temperature.
The MAX symbol will appear
MAX
NOTE: Min/Max readings are automatically cleared daily at 00:00
Press to view the minimum or maximum temperatures of the
local and remote channels 1 to 4.
CHN
1
1
L
Replace the batteries when the Low Battery Indication lights up on
the LCD screen by the local (indoor) temperature display
NOTE: After replacing the batteries, you will need to perform the Setup
and Learn Function procedures again. Refer to the GETTING STARTED
and WIRELESS TRANSMISSION sections.
Replace the batteries when the Low Battery Indication lights up on
the bottom-left corner of the LCD screen on the WT440 transmitter
When the batteries are low on a transmitter a Low Battery Indication
w
particular channel.
MINIMUM
MAXIMUM
A
B
B
C
3
4
B
*
A
*
*
2
2
3
3
4
4
1
1
2
1
2
3
*
4
TEMPERA
The is an ideal feature to be used for greenhouses
and wine cellars, or any place that you require controlled temperature.
Once activated, the temperature alarm would sound when the room gets
too warm or too cold depending on your settings.
temperature alarm
Y can set both an upper and lower temperature alarm for the local
temperature (main receiver unit) and/or for each of the remote
(outdoor) channels of 1 to 4.
Scroll to the Upper T Alarm Setting mode by pressing .
Y should see the symbol and dotted lines ( ) or pre-existing
setting blink.
MODE
---
Select the desired channel, local or remote channels (1 to 4) using .CHN
Press to finish; or rMODE epeat steps for all
other channels if desired.
Press or key to set the desired value for the upper temperature limit.+-
T disable the particular alarm, press .
The dotted lines ( ) would reappear to indicate
that the alarm has been disabled.
ALARM
---
Setting the Upper T
UPPER TEMPERATURE LIMIT warmIf the temperature gets too
and reaches the upper temperature limit, the alarm would sound.
LOWER TEMPERATURE LIMIT coldIf the temperature gets too
and reaches the lower temperature limit, the alarm would sound.
1
2
3
*
4
TEMPERA
Scroll to the Lower T Alarm Setting mode by pressing .
Y should see the symbol and dotted lines ( ) or pre-existing
setting blink.
MODE
---
Select the desired channel, local or remote channels (1 to 4) using .CHN
Press to finish; or rMODE epeat steps for all
other channels if desired.
NOTE: In the normal clock display, when either the upper or lower
temperature alarm has been set for a particular channel, the or
symbol will show up solid on the LCD screen when that channel is displayed.
Press or key to set the desired value for the lower temperature limit.+-
T disable the particular alarm, press .
The dotted lines ( ) would reappear to indicate
that the alarm has been disabled.
ALARM
---
Setting the Lower T
When the T
The temperature alarm will sound when the actual temperature has
reached (or exceeded) the upper or lower temperature limit.
The temperature alarm has a distinctive tone different to that of
the clock alarm.
or symbol and temperature limit will blink
Press ANY key to stop the temperature alarm. Or without interruption,
the temperature alarm will automatically stop after one minute.
C
A
1
2
3
5
4
P
P
P P P
P P P
1
3
2
