Bedienungsanleitung Urmet 1067-026 (Seite 5 von 12) (Deutsch, Englisch, Italienisch)

741489

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

DS1067-058 5

ENGLISH

GENERAL DESCRIPTION

Keypad with tempered glass front side, “soft-touch” technology and OLED display.

This allows to control and program the 1067 series systems, is equipped with a proximity key reader

1067/332, 1 programmable auxiliary entries and one microphone for environment listening (by phone with

PSTN or GSM interface). Furthermore, it is provided with a vicinity sensor that allows the activation of full

functionality of the device that is typically in a state of low consumption; placing the hand near the area

above the logo switches on the backlight, the display shows the predefined information and the key reader

becomes active. After 30 seconds from the last action, the keypad returns to standby mode.

Besides the usual alphanumeric and navigation keys, there are 4 additional keys available whose

functions, when activated, are visible by means of an icon on the above display area.

POSITIONING

Keypad must be positioned:

 in an environment that is sheltered and protected from water and

humidity;

 on a dry and level wall;

 in the proximity of the accesses to area to be protected;

 in an inner location which is not subjected to excessive sudden

rises/falls in temperature, and is protected by anti-burglar system;

 at 160 cm height for normal installations, or at 120 cm height for

installations suitable to disabled users.

WIRING

Keypad can be connected on bus either in a cascade or star. Keypad position along bus is not important.

The overall length of all bus sections must not exceed 400 metres. For wiring, use 4 lead screened cable

(2 leads for power supply and 2 leads for data connection). Lead section must be chosen taking into

account voltage drop caused by connection length.

In counting out overall system absorption, also consider max consumption in keypad (110 mA).

INSTALLATION

The 1067/026 keypad can be installed either on a wall or above a round, flush mounting box or 3-seated

built-in case. To install the keypad proceed as follows:

 Remove the keypad from the wall bracket by sliding it (Fig.1).

 Secure the support bracket to the wall with 6 mm plugs (provided), or on the built-in case if available,

keeping the terminal strip downwards (Fig.2) using the mountings “A’ or “B”. Avoid over-tightening the

screws, in that they may cause the bracket to curve, making it difficult to assemble the keypad onto the

bracket itself

 For the anti-removal, use two plugs supplied at the holes "C" and fix also block "D".

 Connect the cable to the terminal board “E”.

 Insert the cable that comes out of the keypad into the dedicated connector

“F”. Place the cable so that

it fits into the specially designed space at the bottom of the keypad; this prevents it from being crimped

when assembling the keypad to the bracket.

 Insert the keypad block in the bracket and slide it downwards.

 Secure with locking screws “G” (Fig.3).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Urmet 1067-026 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info