706169

Uspeed Wifi repeater Seite 5

5
Zoom out
Zoom in
Vorherige Seite
1/10
Nächste Seite
- 8 -
- 7 -
3. Temporarily change the IP address of your computer
From the IPv4 settings, switch to configure your IP
address manually.
Type in the following settings:
• IP address: 192.168.10.111
• Subnet mask: 255.255.255.0
• Default gateway/Router: 192.168.10.1
• Note: Do not change DNS settings
Click “OK” and wait a few seconds to allow the new
settings to apply.
Step 1. Confirm Live Internet Connection
Please verify that your router or DSL modem is working
properly and that your existing devices can connect to
the Internet successfully.
Step 2. Select Repeater Location
Identify the wall socket where you would like to place
the repeater. Ensure that your desired location has a
stable Wi-Fi signal from your original router. > 70%
signal strength is ideal, while signals < 50% strength may
reduce your network speed and connection stability.
Step 3. Connect Computer to your Repeater
1. Plug the repeater into a wall socket; allow a 1-minute
start up time.
2. Connect your computer to the repeater wirelessly:
From your computer, view your available wireless
connections (typically accessible from the corner
of your desktop).
Choose the newly available “WiFi-Repeater”
network and connect. Note that no password is
needed at this time.
Step 4. Temporarily change the IP address
setting of your computer
1. Open the IP setting dialog on your computer
For PC users
Windows 7
Go to Start > Control Panel > Network & Sharing
Center > Change Adapter Settings (or Manage
Network Connections).
Windows XP
Go to Start > Control Panel > Network Connections.
Among the list of connections, right click
“Wireless Connection.”
Click “Properties” in the pop-up menu. The
“connection properties” window will appear.
In this window, double click “Internet Protocol
Version 4(TCP/IPv4).” The IP setting dialog will
appear.
b.
c.
For Mac users
Click the Wi-Fi icon from the top-right corner
of your desktop and choose “Open Network
Preferences.” The network configuration window
will appear.
On the left of the window, select your Wi-Fi
connection. Then click “Advanced…” on the lower
right side.
Select the TCP/IP tab, and the IP setting page will
appear.
2. Record the current IPv4 settings before proceeding
Note: Computers are often set to “Obtain an IP
address automatically” via the DHCP setting. If it is
not, you need to write down the exact information of
your IP address, subnet mask and default gateway.
3. Temporarily change the IP address of your computer
From the IPv4 settings, switch to configure your IP
address manually.
Type in the following settings:
• IP address: 192.168.10.111
• Subnet mask: 255.255.255.0
• Default gateway/Router: 192.168.10.1
• Note: Do not change DNS settings
Click “OK” and wait a few seconds to allow the new
settings to apply.
Step 5. Logon to the Repeater Settings
1. Open a web browser on your computer, and type
192.168.10.1 to reach the repeater’s static IP address. A
log-on dialogue will be displayed.
2. Enter your User/Password: admin/admin to logon to
the configuration web page of your repeater.
Step 6. Configure the Repeater
1. Click “Setup Wizard” on the left of page.
2. Choose “Wireless Repeater Mode (Station),” then click
“Next”
3. Click “Repeater - OneKey Setting”
4. After scanning, a list of available wireless AP (access
point) networks will be displayed on the page. Select
the SSID (access point name) of your existing wireless
router, then click “Next.”
5. Configure security information:
Do not change the default values above “Pre-Shared
Key”. These values reflect your settings from your
existing router signal and have been detected by the
repeater to ensure compatibility.
In the “Pre-Shared Key” field, type your existing
wireless router’s password.
6. Click “Apply and Reboot,” then click “Yes.” Wait 1
minute for the repeater to restart completely.
Step 7. Restore your Computer’s Original IP
Address Settings
Follow the same process from Step 4, and restore your
original / recorded IP address settings.
Step 8. Connect your Computer to the Newly
Configured Repeater
1. From your computer, view your available wireless
Step 1. Confirm Live Internet Connection
Please verify that your router or DSL modem is working
properly and that your existing devices can connect to
the Internet successfully.
Step 2. Select Repeater Location
Identify the wall socket where you would like to place
the repeater. Ensure your router / DSL modem is close
enough to connect to by cable.
Step 3. Connect Repeater to Network Socket
and Computer
1. Plug one end of your network cable into the router
network socket, and the other end into the port of the
repeater.
2. Plug the repeater into a wall socket; allow a 1-minute
start up time.
3. Connect your computer to the repeater wirelessly:
From your computer, view your available wireless
connections (typically accessible from the corner
of your desktop).
Choose the newly available “WiFi-Repeater”
network and connect. Note that no password is
needed at this time.
Step 4. Temporarily change the IP address
setting of your computer
1. Open the IP setting dialog on your computer
For PC users
Windows 7
Go to Start > Control Panel > Network & Sharing
Center > Change Adapter Settings (or Manage
Network Connections).
Windows XP
Go to Start > Control Panel > Network Connections.
Among the list of connections, right click
“Wireless Connection.”
Click “Properties” in the pop-up menu. The
“connection properties” window will appear.
In this window, double click “Internet Protocol
Version 4(TCP/IPv4).” The IP setting dialog will
appear.
Click the Wi-Fi icon from the top-right corner
of your desktop and choose “Open Network
Preferences.” The network configuration window
will appear.
On the left of the window, select your Wi-Fi
connection. Then click “Advanced…” on the
lower right side.
Select the TCP/IP tab, and the IP setting page
will appear.
2. Record the current IPv4 settings before proceeding
Note: Computers are often set to “Obtain an IP
address automatically” via the DHCP setting. If it is
not, you need to write down the exact information of
your IP address, subnet mask and default gateway.
… 5 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Uspeed Wifi repeater wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Uspeed Wifi repeater

Uspeed Wifi repeater Bedienungsanleitung - Deutsch - 11 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info