Bedienungsanleitung V-Zug Supremo SL (Seite 18 von 199) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Schwedisch, Norwegisch)

503142

Zoom out

Zoom in

Vorherige Seite

1/199

Nächste Seite

Adjust time

To adjust the time on the display, proceed as follows:

1. Press the P / ESC button (B7) to enter the settings menu.

2. Press the ▽ and △ buttons (B5 and B6) until “ADJUST

TIME” is displayed;

3. Press the OK button (B4). The hours ash on the display;

4. Press the ▽ and △ buttons (B5 and B6) to change the

hours;

5. Press the OK button (B4) to conrm. The minutes ash on

the display;

6. Press the ▽ and △ buttons (B5 and B6) to change the

minutes;

7. Press the OK button (B4) to conrm;

8. Press the P / ESC button (B7) to exit the settings menu.

Auto-start

You can set the auto-start time in order to have the appliance

ready at a certain time (for example in the morning) so you can

make coee immediately.

Please note:

To enable this function, the time must be set correctly.

To enable Auto-on, proceed as follows:

1. Press the P / ESC button (B7) to enter the settings menu.

2. Press the ▽ and △ buttons (B5 and B6) until “AUTO

START” is displayed;

3. Press the OK button (B4). “ENABLE?” is displayed;

4. Press the OK button (B4). The hours ash on the display;

5. Press the ▽ and △ buttons (B5 and B6) to choose the

hours;

6. Press the OK button (B4) to conrm. The minutes ash on

the display;

7. Press the ▽ and △ buttons (B5 and B6) to change the

minutes;

8. Press the OK button (B4) to conrm. “ENABLED” appears

under “AUTOSTART”.

9. Press the P/ ESC button (B7) to exit the menu.

To disable the function:

1. Press the P / ESC button (B7) to enter the settings menu.

2. Press the ▽ and △ buttons (B5 and B6) until “AUTO

START” is displayed;

3. Press the OK button (B4). “DISABLE?” is displayed;

4. Press the OK button (B4) to conrm;

5. Press the P/ ESC button (B7) to exit the menu. “DISABLED” is

displayed.

Auto-o (Standby)

The appliance is set by default to go o if not used for two

hours.

The time can be changed so that the appliance switches o after

15 or 30 minutes, or after 1, 2 or 3 hours.

To re-programme Auto-o, proceed as follows:

1. Press the P / ESC button (B7) to enter the settings menu.

2. Press the ▽ and △ buttons (B5 and B6) until “AUTOOFF”

is displayed;

3. Press the OK button (B4);

4. Press the ▽ and △ buttons (B5 and B6) until the required

time (15 or 30 minutes, or 1, 2 or 3 hours) is displayed;

5. Press the OK button (B4) to conrm;

6. Press the P/ ESC button (B7) to exit the menu.

Auto-o is programmed.

Setting the temperature

To modify the temperature of the water used to make the coee,

proceed as follows:

1. Press the P / ESC button (B7) to enter the settings menu.

2. Press the ▽ and △ buttons (B5 and B6) until “SET TEMPE

RATURE” is displayed;

3. Press the OK button (B4);

4. Press the ▽ and △ buttons (B5 and B6) until the required

temperature is displayed (l = low, llll = high);

5. Press the OK button (B4) to conrm;

6. Press the P/ ESC button (B7) to exit the menu.

Setting water hardness

The operating period can be extended if required, making desca-

ling less frequent by programming the machine on the basis of

the real lime content in the water used.

Proceed as follows:

• Removethe“TotalHardnessTest”strip(attachedtopage2)

from its packaging then dip it fully in the water for a few

seconds.

Remove and wait about 30 seconds (until it changes colour

and forms red squares).

• Turn the appliance on by pressing the ON/OFF/standby but-

ton (A7).

• Press the P / ESC button (B7) to enter the menu and then the

▽ and △ buttons (B5 and B6) until “WATER HARDNESS” is

displayed.

• Press the OK button (B4);

• Press the ▽ and △ buttons (B5 and B6) until the number

coincides with the number of red squares on the test strip

(for example, if there are 3 red squares on the test strip, se-

lect the message “WATER HARDNESS lll” .

• Press the OK button (B4) to conrm.

The coee machine is now programmed to provide the de-

scale warning when actually necessary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

V-Zug Supremo SL Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info