602548
19
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
On-roof fitting and installation 4
0020077994_02 auroTHERM exclusive Installation manual 19
4.1.6 Determining the number of required roof
brackets
1. Ask the local building authority for the regional max-
imum snow load s
k
.
Conditions: Maximum snow load: 3 kN/m²
Install 4 roof brackets per collector.
Conditions: Maximum snow load: 3 < × 4.5 kN/m²
Install 6 roof brackets per collector.
Conditions: Maximum snow load: > 4.5 kN/m²
Compile statistics for the individual case.
Ensure that the maximum permissible snow load per
collector is 5.4 kN/m².
Note
The maximum permissible load per roof
bracket type S/type P is: F
max
= 1.875 kN.
2. If you are using extension sets, ensure that the roof
bracket is positioned centrally with equal clearances.
4.1.7 Defining the edge clearances of the roof
brackets
Maximum lift points caused by wind loads can occur at
the cut-away edges of wall and roof areas (e.g. verge and
eaves). These maximum lift points result in high loads on
the collectors and installation systems.
Areas in which lift points occur are called edge areas.
Corner areas are zones in which edge areas overlap and
especially high pull forces occur.
Edge and corner areas must not be used as installation
areas.
e
lang
e
kurz
h
b
l
b Building width
h Building height
l Building length
Calculate the building width w, building height h and
building length l.
The values for the edge clearances to be observed, e
short
and e
long
can be found in the following tables.
b
[m]
H [m]
5 6 7 8 9 10 11 12 13 14 15
8 1.0
9 1.0
10 1.0
11 1.0 1.1
12 1.0 1.2
13 1.0 1.2 1.3
14 1.0 1.2 1.4
15 1.0 1.2 1.4 1.5
16 1.0 1.2 1.4 1.6
17 1.0 1.2 1.4 1.6 1.7
18 1.0 1.2 1.4 1.6 1.8
l
[m]
h [m]
5 6 7 8 9 10 11 12 13 14 15
10 1.0
11 1.0 1.1
12 1.0 1.2
13 1.0 1.2 1.3
14 1.0 1.2 1.4
15 1.0 1.2 1.4 1.5
16 1.0 1.2 1.4 1.6
17 1.0 1.2 1.4 1.6 1.7
18 1.0 1.2 1.4 1.6 1.8
19 1.0 1.2 1.4 1.6 1.8 1.9
20 1.0 1.2 1.4 1.6 1.8 2.0
When installing the roof brackets, observe the calculated
edge clearances.
4.1.8 Defining the roof bracket clearances
The roof brackets have different clearances depending on
the array configuration of the collectors (adjacent or on top
of each other).
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Vaillant auroTHERM exclusive VTK 570-2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Vaillant auroTHERM exclusive VTK 570-2

Vaillant auroTHERM exclusive VTK 570-2 Installationsanweisung - Holländisch - 60 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info