Bedienungsanleitung Vaillant ecoVIT exclusiv VKK 226-4 (Seite 6 von 16) (Englisch)

748580

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

3 Product description

6 Operating instructions ecoVIT exclusiv 0020258609_00

3 Control (accessory)

4 Main switch

5 + button

6 − button

7 Reset button

8 Heating flow temperat-

ure rotary knob

9 Cylinder temperature

rotary knob

The display shows the current heating flow temperature, the

filling pressure of the heating installation, the operating mode

or certain additional information.

The i button is used to call up status information.

The control, which is available as an accessory, automatic-

ally controls the flow temperature depending on the outdoor

temperature.

The main switch is used to switch the product on and off.

The + button is used to display the cylinder temperature (if

the product is equipped with a cylinder temperature sensor).

The − button is used to display the filling pressure of the

heating installation.

The Reset button is used to reset the product in the case of

certain faults.

The heating flow temperature rotary knob is used to set the

heating flow temperature if no control is connected. If a con-

trol is connected, the heating flow temperature rotary knob

should be turned clockwise as far as it will go.

The cylinder temperature rotary knob is used to set the cyl-

inder temperature if a domestic hot water cylinder is connec-

ted.

If a control is connected, the rotary knob should be turned

clockwise as far as it will go. The control then determines the

cylinder temperature.

3.3.1 Digital Information and Analysis System

(DIA)

1 Display showing the

current heating flow

temperature, the filling

pressure in the heating

installation, or a status

or fault code

2 Plain text display

3.3.2 Displayed symbols

Symbol Meaning Explanation

Fault in the air/flue gas

route

Fault in the air/flue gas

route

Symbol Meaning Explanation

comDIALOG The heating flow and do-

mestic hot water temper-

ature are specified via

the comDIALOG com-

munications system. The

product works at temper-

atures other than those

set at the rotary knob.

This operating mode can

only be terminated by:

– comDIALOG

– Changing the tem-

perature at the rotary

knobs by more than

± 5 K

This operating mode

cannot be terminated by:

– Pressing the Reset

button.

– Switching the

product off and on

again

Heating mode – Symbol perman-

ently on: Product is

in heating mode op-

erating mode

– Symbol flashing:

Burner anti-cycling

time is active

Hot water generation – Symbol permanently

visible: Charging

mode for the do-

mestic hot water

cylinder is enabled

by the control and

floor-standing boiler

control system

– Symbol flashes:

Domestic hot water

cylinder is being

heated

Heating pump operating

Solenoid valve is actu-

ated

Gas supply to the burner

is open

Current energy demand Display of the current

burner modulation rate

(bar graph display)

Fault during burner

operation

Burner is switched off

Burner operating cor-

rectly

Burner is switched on

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vaillant ecoVIT exclusiv VKK 226-4 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vaillant ecoVIT exclusiv VKK 226-4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info