Bedienungsanleitung Valera Valera Premium Protect 1200 (Seite 7 von 82) (Alle Sprachen)

821563

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

INSTALLATION INSTRUCTIONS

Wall holder model 044.01 - 044.02 -

044.03 - 044.04 - 044.05 - 044.06

Model 044.01 (Fig. 1)

Basic model with ON-OFF switch.

Model 044.02 (Fig. 2)

Model with 16 A European standard socket and ON-OFF switch.

Model 044.03 (Fig. 3)

Model with 10 mA (*) differential switch, 16 A European standard

socket and ON-OFF switch.

Model 044.04 (Fig. 4)

Model with 10 mA (*) differential switch and ON-OFF switch.

Model 044.05 (Fig. 5)

Model with universal shaver socket (**) and ON-OFF switch.

Model 044.06 (Fig. 6)

Model with 10 mA (*) differential switch, universal shaver socket

(**) and ON-OFF switch.

(*) The appliance is equipped with a 10 mA differential switch.

(**) A safety transformer isolates the shaver socket from the

mains electricity and a protective device prohibits the use of

appliances with a power greater than 20 VA.

Installation of wall holder

This work should only be carried out by a suitably qualified electrical

engineer, in order to comply with the existing national safety regulations.

When the spiral cord is extended to its maximum length, the hairdryer

shall not be reached by a person using the bath or the shower.

There are two possible methods of installation:

A = for fixed connection lead

B = for mobile connection lead

Attention: before installing the hairdryer

always switch off the general switch

of your mains electricity.

Method A (for fixed connection lead) for

wall holder model 044.01 - 044.04

044.05 - 044.06

The connection wiring from the mains for wall holder models

044.01 - 044.04 - 044.05 - 044.06 must be type 2x1,5 mm2.

1. Separate the cover (1) of the wall holder from the back plate by

loosening the screw (14).

2. Remove the knockout (2) provided in the back plate of the wall

holder.

3. Feed the mains supply cable (3) coming out of the wall into the

hole in the back plate left after removing the knockout (2).

4. Secure the back plate of the wall holder to the wall using the plugs

and screws provided.

5. Remove the terminal connector (4), connect the mains supply

cable (3) to the terminal connector (4), as shown in the picture, and

then secure again the terminal connector (4).

6. Model 044.01 - 044.04 - 044.05 - 044.06 are double insulated

and no earth connection is provided.

7. Fit the front cover of the wall holder, taking care to locate the cable

sleeve (6) properly. Secure the front cover with the screw (14).

8. Switch on the general switch of your mains electricity. The

hairdryer is ready for use.

Method B: (for mobile connection lead)

only for wall holder model 044.01 - 044.04

044.05 - 044.06

The connection wiring from the mains for wall holder models 044.01

044.04 - 044.05 - 044.06 must be type H05VV-F 2x1,5 mm2.

1. Separate the cover (1) of the wall holder from the back plate by

loosening the screw (14).

2. Remove the knockout (8) provided in the base of the back plate

of the wall holder for feeding the cable sleeve (11).

3. Secure the back plate of the wall holder to the wall using the plugs

and screws provided.

4. Strip the power supply connection cable (13), insert the cable

bushing (11), remove the terminal (9), connect the cable (13) to

the terminal (9) and reposition the terminal (9). Position the

stripped part of the cable carefully, as indicated in the picture.

Secure the cable bushing (10) using the corresponding screws.

Caution: this appliance has double insulation and is not fitted with

an earthing system.

5. Locate the cable sleeves (6) and (11) in the slot provided in the

base of the back plate.

6. Fit the front cover of the wall holder, taking care to locate the cable

sleeves (6) and (11) properly.

7. Secure the front cover with the screw (14).

8. Switch on the general switch of your mains electricity. The

hairdryer is ready for use.

Method C (with mobile connection) for

models 044.02 - 044.03

See Method B: only variant:

- The power cable for mounts 044.02 - 044.03 must be type

H05VV-F 3G x 2.5 mm2and must be connected to the tripolar

terminal (7)

OPERATING INSTRUCTIONS

Switching

Wall mount switch (Fig. 7, 1)

appliance placed in the mount = off

appliance out of the mount = on

Differential switch

(Mod. 044.03, 044.04, 044.06 only)

The differential switch (Fig. 9 and 10), in the event of a fault in the

electrical circuit to which it is connected, is triggered and cuts off the

power supply to the mount and the hair dryer. (Fig. 9)

•Allow your appliance to cool before storing away and do not wrap the

supply cord around the hairdryer in storage.

•The A-weighted sound pressure level of the hairdryers for commercial use

is below 70 dB(A).

00060753 int_giu2018_Layout 1 05/06/2018 12:46 Pagina 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Valera Valera Premium Protect 1200 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info