Bedienungsanleitung Varde Fuego (Seite 14 von 22) (Englisch)

813312

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

How to light and stoke a fire

The first time you light up the stove, the enamel will temper and give off some smoke and a

slightly burnt smell. We recommend that you leave doors and windows open, as airing the room

will make the smell disappear.

This tempering softens the enamel, making it susceptible to damage. Therefore exercise caution

and avoid touching the enamel. We also recommend opening the door to the stove at regular

intervals during the first couple of hours to prevent the rope seal from sticking to the enamel.

Never use highly flammable liquids such as methylated spirit or petrol for lighting up!

We recommend using ‘top-down’ lighting, where you light the wood at the top of the combustion

chamber and not at the bottom. This is the most environmentally friendly method to light a fire.

The method will also help keep the glass clean. Place four small logs in a cross on the bottom

plate of the combustion chamber (approx. 1.5 – 2 kg) with a small distance between each log.

Place 8 – 12 smaller sticks (0.5 – 1 kg) in a cross on top of the logs, and 2 – 3 firelighters at the

top and in between the sticks.

A thin layer of ash at the bottom of the stove makes it easier to light the fire.

Before lighting the stove, open the shaking grate by pulling the small lever under the combus-

tion chamber completely towards the right. Pull the lever underneath to the right as well to allow

the ignition air to enter and pull the combustion air damper towards the right until it is com-

pletely open.

Once the fire burns, remember to close the ignition air vent and shaking grate again. Otherwise,

the stove and chimney might become overheated, which would invalidate the warranty.

Once the kindling has reduced to embers, we recommend opening the door slightly for a couple

of seconds to neutralise the negative pressure in the combustion chamber before opening the

door completely.

Place 3 – 4 logs in a cross on top of the embers (approx. 2 kg) and close the door again. To

make sure the wood ignites quickly, we recommend briefly opening the ignition air vent and

make sure you remember to close it again once the fire gets going. You can then adjust the

combustion air according to your heating requirements.

Take care not to shut off the air supply completely, otherwise the fire will die. The fire should

always burn bright and clear.

In most instances, however, you will have to identify the best combustion air settings your-

self, as the height and draught of your chimney as well as the quality of the firewood are deci-

sive factors in determining the best settings for your particular stove.

If the nominal heat output of your stove is too high compared to your heating requirements, you

can reduce the output as follows:

- Stoke a smaller amount of wood than usual, for example 1.2 – 1.3 kg, preferably consisting of

3 – 4 smaller pieces of wood. Apply full air to ignite the wood properly before reducing the com-

bustion air, perhaps down to approx. 60%. Be careful not to reduce the air supply to the point

that the fire dies. The fire should always burn bright and clear.

With this method it is possible, depending on the chimney, wood quality, etc., to reduce the

stove’s heat output from a nominal 5 kW down to perhaps 3 – 3.5 kW.

Please be aware that it can lead to poor combustion if you reduce the combustion air too much,

resulting in a lower efficiency and increased emission levels (increased pollution).

You may wonder why your stove is fitted with a gap in the rear vermiculite plate in the combus-

tion chamber, with small holes through the back steel plate, but these holes are an important

part of the combustion system. We refer to these air ducts as the ‘tertiary air’. They are an

important part of a clean-burning stove.

When refilling the stove with wood, we recommend opening the stove door once only embers

are left in the combustion chamber. Opening the door while flames are still burning and produc-

ing smoke and gas might cause smoke to escape into the room.

If you have problems lighting or operating the stove, see the section on Troubleshooting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Varde Fuego Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Varde Fuego

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info