Bedienungsanleitung Varde Samso Multi-fuel (Seite 11 von 24) (Englisch)

813320

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

How to Light and Maintain a re:

The rst time the stove is lit the outer casing will temper. To allow the appliance to settle, and fixing

glues and paint to fully cure, operate the appliance at a low temperature for first few days.

During this time the appliance may give off some unpleasant odours. Keep the room well ventilated to

avoid a build-up of fumes. The tempering will soften the outer casing making it susceptible to damage,

exercise caution and avoid touching. Varde Ovne also recommend opening and closing the door at

regular intervals for the first few hours of use to prevent the rope seal from sticking to the finish.

DO NOT use highly inammable uids such as methylated spirits or petrol for lighting the stove.

Varde Ovne recommend a "Top-down" lighting method, where you light the wood in the upper area

of the combustion chamber rather than the base. This method is the most efcient way to light a re,

and will keep the glass clean. In the bottom of the combustion chamber make a cross with 4 small

pieces of wood, with a small distance between each log. On top of them make another cross, using

8-12 smaller pieces of wood, followed by 2-3 kindling blocks on top of them.

Wood burns best on a bed of ash (approx. 25mm (1") deep).

If burning solid fuel place a small amount around the stack in order to heat these during the initial

lighting.

Before lighting open the Primary Air and the Airwash Controls to allow primary air to circulate through

the rebox.

When the re is established close the Primary Air Control to avoid overring, which could invalidate

the warranty.

Add more solid fuel at this stage.

Use the Airwash Control to adjust the heat. Do not close the Airwash Control or the re will die out.

When running the appliance refuel little and often for clean, efcient burning when burning wood.

A bright and clean rebox indicates the appliance is burning well.

Note: The height and draught of the chimney, as well as the quality of the wood being burnt, are

deciding factors in determining optimal combustion.

Experience establishes settings to suit personal preferences.

If the re is running too hot it is possible to reduce the heat output of the stove:

Burn a smaller amount of wood than usual, eg. 1.2-1.3kg, and if possible use 3-4 small pieces of

wood. Apply Primary Air to ignite the wood and then adjust the Airwash Control to around 60%. Do

not close the Airwash Control or the re will die out. Using this method it is possible to reduce the

nominal output of the stove from 5kW to around 3 - 3.5kW.

Important: This method can lead to poor combustion as restricting the Airwash Control too much can

lead to a lower efciency and an increase in smoke and emissions.

Do not use aerosol sprays near an operating appliance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Varde Samso Multi-fuel Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Varde Samso Multi-fuel

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info