Bedienungsanleitung Varo POWX04950 (Seite 5 von 10) (Englisch)

756780

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

POWX04950 EN

 Do not work on materials containing asbestos. Asbestos is considered carcinogenic.

 Warning! Toxic dust! Dust from materials such as lead paint, some types of wood,

minerals and metal, can be noxious.

 Touching or inhaling this type of dust can present a danger to the user or person nearby.

 Wear safety glasses and a dust mask!

 Secure the work piece. Use clamps or a vice to secure the work piece. This is much safer

than holding it in your hand.

 Never place your hand next to or in front of the device and the surface you are working on,

as slipping poses a risk of injury.

 In the event of danger, immediately pull the mains plug out of the socket

 Always run the mains cable away from the appliance and toward the rear

 Avoid contact with the sanding sleeve in motion.

 Do not work on moistened materials or damp surfaces.

 Always apply the device to the working surface when switched on. When the task is

complete, lift the appliance off the work pieces before switching it off.

 Always firmly hold the device with both hands whilst working. Ensure you have a solid

stance.

 Allow the device to come to a complete stop and switch off before putting it down.

 Always unplug from the mains socket before taking breaks, especially working on the

device (e.g. replacing sandpaper) and during non-use.

7 ASSEMBLY

Warning! Risk of injury! Always unplug from the mains before working on

the sanding brush.

7.1 Fitting and removing accessories (Fig. 1-2)

 Press the spindle lock button.

 Remove the securing screw with the hex hey.

 Push the sanding accessory onto the tool holder.

 Secure by refitting the securing screw.

Sanding accessories can only be fitted one way. The sanding accessory

must slide on easily. Do not attempt to force it onto the tool holder. Check

the correct direction of the sanding accessory.

 Fit the sanding roller as described above.

 Press the spindle lock button and turn the sander by hand until the spindle lock engages.

 Turn the sanding belt anti-clockwise along with the slots on the sanding roller.

7.2 Installing the dust extraction hood (Fig. 3)

 Insert the dust extraction hood (2) into the two fastening grooves (11) on the tool arm (10)

against slight resistance.

 Tighten the clamping screw (4). The dust extraction hood (2) is now firmly installed on the

tool arm (10).

7.3 Adjusting the dust extraction hood (Fig. 4)

 Adjust the dust extraction hood (2) so dust or sparks are not directed at the user.

 The dust extraction hood (2) can cover the grinding spindle from various angles. Use the

locking grooves (12) for this purpose.

 Following installation, loosen clamping screw (4) rotate the dust extraction hood (2) toward

the handle (6) according to the application and the work piece and tighten the clamping

screw (4). The dust extraction hood (2) will lock into place in several positions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Varo POWX04950 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Varo POWX04950

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info