Bedienungsanleitung Varo POWX07583 (Seite 10 von 16) (Englisch)

756782

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

POWX07583 EN

11.3 Adjustment of the turntable (Fig. 4-5)

 Turn the turntable locking knob (9) approx. 2 turns counter-clockwise, then adjust the

turntable (11) by pressing the angle adjustment control button (23).

 The turntable (11) has locking points at angles of 0°, 15°, 22.5°, 31.6° and 45°. Once the

turntable (11) is engaged, the setting must also be secured by turning the turntable locking

knob (9) clockwise.

 If different angle settings are required, the turntable (11) may be secured in position using

only the turntable locking knob (9).

11.4 Adjustment of the bevelling angle (Fig. 6)

The support arm can be tilted vertically and in an angle of 45° to the left.

To be able to tilt the support arm, the bevel lock (16) must be released.

To prevent the bevel angle from changing while sawing, the locking knob of

the support arm must be tightened.

11.5 Adjusting options table parallel fence (Fig. 7)

 The table parallel fence (4) is mounted on the top saw table. The table parallel fence

locking knob (5) must point towards the front of the machine.

 The location of table parallel fence decides the cutting width. When the table parallel fence

is installed, you must always make sure that the guide is fastened with the locking knob

(5).

 Once the locking knob is released, the table parallel fence (4) can be removed.

11.6 Connection to a dust collector

The dust of some types of wood (such as for instance beech, oak and ash)

can be hazardous if inhaled. Always use a dust collector:

 If the saw is set up in an enclosed space;

 Whenever the saw is being used for longer periods of time (more than a half hour per

day);

 When sawing oak-, beech- or ashwood.

 The dust collector must conform to the following requirements:

 The diameter of the dust exhaust pipe must fit properly (31 mm);

 The air flow volume must exceed 550m³/h;

 The vacuum at the dust exhaust exit must be ≥ 740 Pa;

 The air speed at the dust exhaust exit must be ≥ 20 m/s;

 Follow the user instructions for the dust collector.

11.7 Assembly of dust bag (Fig.8)

 The dust bag (28) fits the mitre saw dust hole (27). To ensure efficient operation, empty

the dust bag when it is half-full.

 Never use the machine without the suction function. Regularly check and clean the suction

channels.

11.8 Laser line (Fig.9)

 Operate the ON/OFF switch for the laser light (34) during operation.

11.9 Work-light (Fig. 10)

 The combination saw is equipped with a work-light (31) under the top saw table, powered

by 3pcs AAA batteries.

 To switch the work-light on, press the ON/OFF switch for work-light (32) marked “I”;

 To switch the work-light off, press the ON/OFF switch for work-light (32) marked “O”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Varo POWX07583 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Varo POWX07583

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info