Bedienungsanleitung Varo POWXG6310 (Seite 8 von 21) (Englisch)

756792

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

POWXG6310 EN

flashes this will indicate that wire loop is interrupted, and then mower will not

work.

7.3 Charging the lawnmower

Your robotic lawnmower´s battery may be charged to a certain degree on delivery, but it´s

recommended to fully charge the battery of the lawnmower before use. To charge your robotic

lawnmower follow these steps:

1. Switch the robotic lawnmower on. The On/Off switch (6) is located at the bottom

side of the robotic lawnmower (FIG A and Fig 2).

Note: Your robotic lawnmower will not charge when it is not turned on.

Note: The robotic lawnmower will enter a self-checking state (normally within

5 seconds) after entering the password or when the power is interrupted

during mowing or charging (indicated by a flashing status light). If the mower

is in a self-check state, you will not hear a sound when pressing a button and

the buttons won´t work.

2. Slide the robotic lawnmower into the charging station to charge.

3. Check the indicator on the charging station. The red power light turns up and the

robotic lawnmower charges (green light flashes). If the power light does not light up,

you should check the mains plug of the power supply is plugged in properly and that

the mower is in the station correctly.

4. It takes about 180 minutes to get the battery fully loaded.

7.4 Setting up the perimeter wire (Fig 3, Fig 4 and Fig 5)

The wire defines the borders of the mowing area. Everything in the inner area belongs to the

mowing area, everything in the outer area doesn´t belong to the mowing area. The wire also

serves to mark obstacles and exclude them from the mowing area.

1. Feed the end of the perimeter wire through the groove on the front at the bottom

side of the charging station, until it appears on the rear side (Fig 3).

2. Carefully strip off 10-15 mm of the insulation of the wire.

Note: You should keep a length of 15-20 cm at start and the end of the wire for

operating and handling the wire.

3. Connect the wire to the right hand (black) B terminal of the charging station (Fig 4).

4. Start installing the perimeter wire from the charging station in a clockwise direction

(Fig 5). Pull the wire from the coil, tauten and fix it with one peg. Use a mallet to

insert them in the lawn. Ensure the wire is straight and in line with the charging

station groove for 1.5 m.

5. Recommended distance between pegs is 50 to 75 cm (max).

6. Continue to set the wire around the perimeter of the mowing area.

7. For a more accurate perimeter, we advise that you leave less than 75 cm between

pegs when wiring objects (like flower beds, bushes, trees and other items).

Loose wire can be cut during mowing. Make sure the wire is flat to the ground.

Use additional pegs where the wire is slack. The wire is taut before placing the

next peg (if you can place a couple of fingers under the wire this is not taut

enough). Increase the number of pegs at a corner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Varo POWXG6310 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Varo POWXG6310

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info