Bedienungsanleitung VAX Cadence V 094 (Seite 4 von 4) (Englisch)

540971

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

roubleshooting / UK Service & Help / Technical Specification

irt Container & Filters: Removal & Replacement / Storage

9. Troubleshooting

WARNING: To reduce the risk of personal injury, unplug the vacuum cleaner before performing

maintenance/troubleshooting checks.

PROBLEM: Vacuum cleaner won't run

Cause:

Not properly plugged into electrical outlet.

Solution: Plug in securely.

Cause: No electricity in the electrical outlet.

Solution: Check fuse or breaker.

Cause: On/off switch not turned on.

Solution: Push on/off switch to ‘on’.

Cause: Motor thermostat has tripped.

Solution: Switch off and unplug the vacuum cleaner. Leave for one (1) hour before switching the

vacuum cleaner back on.

Cause: Blown fuse/tripped breaker.

Solution: Reset circuit breaker or replace fuse.

PROBLEM: Cleaner won’t pick up/loss of suction.

Cause:

Dirt container not installed properly.

Solution: Review dirt container replacement.

Cause: Dirt container full or blocked.

Solution: Empty dirt container.

Cause: Clogged filters.

Solution: Remove, clean and replace filters.

PROBLEM: Accessories won’t pick up.

Cause:

Accessories are not attached correctly.

Solution: Refer to section 5.

PROBLEM: Dust escaping from the vacuum cleaner.

Cause:

Dirt container full.

Solution: Empty dirt container.

Cause: Dirt container not installed correctly.

Solution: Review dirt container replacement.

Cause: Hose not installed correctly.

Solution: Review installation.

Cause: Filter not installed completely.

Solution: Remove, clean and replace filters.

6. Dirt Container & Filters: Removal

& Replacement

IMPORTANT: Always unplug the vacuum cleaner

from the electrical outlet before removing the dirt

ontainer.

IMPORTANT: Do NOT use the vacuum cleaner

without ALL of the filters in place.

Emptying the Dirt Container

1. Press the button located on the top carry handle

to access the dust container (Fig 6/1)

2. 2. Remove the dust container by pulling the

handle (Fig 6/2)

3. Press the button located on the rim of the dust

container to empty the dirt into a rubbish bin

(Fig.6/3)

When all of the dirt has fallen, close the dirt

container flap, close the safety latch and replace the

dirt container

Cleaning the Filter

1. Remove the dust container as directed.

2. T

wist the filter safety catch located on top of the dust

container and pull out the central filter unit (Fig 6/4)

3. Gently tap the filter against the side of a rubbish

bin to remove excess dirt.

. The central filter can be washed in warm water

[

max 40

]. Allow to air dry completely before

eplacing.

NOTE: Do NOT use any detergents or boiling water

to wash the filter. Vax recommends replacing the filter

every 9-12 months.

. Replace the central filter unit to the dust container

ensuring the filter safety catch has been reset.

6. Replace the dust container as directed.

Post-motor Filter

NOTE:

This is located on the back of the vacuum

cleaner.

1. Release the post-motor cover and remove the

filter by pressing in the catch on the back of the

vacuum cleaner.

2. The post-motor filter can be washed in warm

water [max 40

C]. Allow to air dry for 24 hours

before replacing.

3. Replace the post-motor filter and cover before

re-starting the vacuum cleaner.

NOTE: Do NOT use any detergents or boiling water

to wash the filter. Vax recommends washing the filter

every 9-12 months.

7. Cleaning Blockages

WARNING: To reduce the risk of electric shock, the

power cord must be disconnected before performing

maintenance/troubleshooting checks.

1. Turn the vacuum cleaner off and unplug from the

electrical outlet.

2. The flexible hose can be disconnected fr

om the

vacuum cleaner by pushing in the button on the hose

and pulling away fr

om the machine. Remove any

blockages found then reconnect the hose securely.

3. To remove blockages from the TurboTool, rotate

the locking ring 180

, then turn the TurboTool over.

Pivot the lower housing open, then remove any

obstructions. To re-assemble, ensure the tabs are

engaged, pivot the lower housing closed and re-

position the locking ring.

8. Storage

IMPOR

ANT:

Always unplug the vacuum cleaner

om the electrical outlet and r

ewind the power cord

as dir

ected befor

e storing.

NOTE: Always store the vacuum cleaner base

down.

Fig.6/1

Fig.6/2

Fig.6/4

10. UK Service & Help

Vax Care 0870 6061248

Monday-Friday

. 9.00am to 5.00pm.

An answerphone will be available out of these

hours. Any queries or concerns about using your

Vax, call the Vax Careline. Calls are charged at the

UK national rate.

Please make a not of the model number and serial

number of your Vax before calling. There are over

400 approved Vax Service Agents in the UK. For

the nearest Vax Service Agent, please call the Vax

Careline or visit www.vax.co.uk

www.vax.co.uk

11. T

echnical Specification

oltage:

220-240V ~50Hz

attage:

1600W-1700W (dependant on

model)

Capacity:

2.2 litr

es appr

Filters:

ashable central HEP

A filter

Post-motor filter

Cor

d length:

5.8m (appr

ox)

eight:

7.2kg

Subject to technical change

without notice.

Fig.6/3

V-094 amended aw 1/11/05 11:16 am Page 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

VAX Cadence V 094 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info