Bedienungsanleitung VAX UCSUSHV1 (Seite 16 von 20) (Englisch)

702168

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

• Check the ‘This pack contains’ panel on the box to make sure the part

is included with your vacuum cleaner.

• The plug may not be fully pushed into the electrical socket.

• Check the fuse in the plug if this needs replacing, always replace with a 13amp

British fuse.

• The motor thermostat may have tripped. If this has happened, unplug the vacuum

cleaner. Remove and empty the dirt container and check the hose for blockages.

Clean the lters and allow the vacuum cleaner to cool for approximately 1 hour

(if you have washed the lters you will need to wait 24 hours for the lters to fully

dry before putting them back into the vacuum cleaner).

• The brushbar may not have been activated. Go to ‘Using your machine - The full unit’.

• The vacuum cleaner may not be reclined. Go to ‘Using your machine - The full unit’.

• The lift out cylinder may not be correctly assembled to the back panel and oorhead.

Go to ‘Assembling your upright’.

• The brushbar may be obstructed. Go to ‘Let’s talk technical’.

• The brushbar may need resetting. Go to ‘Let’s talk technical’.

• The belt may be broken. Go to ‘Let’s talk technical’.

• The dirt container may not be tted correctly, remove the dirt container and

re-attach making sure it is clicked rmly into place.

• The air vent is open on the oorhead, reducing the suction. Go to ‘Using your

machine - The full unit’.

• The dirt container may be blocked, empty the dirt container and clean the lters.

Go to ‘Taking care of your machine’.

• There may be a blockage in the hose. Check and clear any blockages. Go to ‘Let’s

talk technical’.

• The brushbar may not be turning. Go to ‘Why isn’t my brushbar rotating?’ below.

• If the accessory/tool will not pick up, check and clear any blockages. Go to ‘Let’s

talk technical’.

• The lters may need cleaning or replacing. Go to ‘Taking care of your machine’.

SolutionProblem

What to do if it goes wrong

There is an

accessory missing

Why does my vacuum

cleaner have no power?

Why won’t the vacuum

cleaner pick up?

Why isn’t my

brushbar rotating?

• If the brushbar has been obstructed, the brushbar motor protection sensor may

have been activated. The brushbar will stop and the light on the oorhead will

illuminate red. Check the brushbar and clear any hair or debris. Go to ‘Let’s talk

technical’.

Why is there a red light

on my oorhead?

• The lters may not be correctly tted. Go to ‘Taking care of your machine’.

• The dirt container may be full or blocked. Go to ‘Taking care of your machine’.

• The lters may need cleaning or replacing. Go to ‘Taking care of your machine’.

• There may be a blockage in the hose. Go to ‘Let’s talk technical’.

Why is dust escaping

from the vacuum?

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

VAX UCSUSHV1 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info