Bedienungsanleitung VAX V-125 (Seite 11 von 20) (Englisch)

540867

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ax Careline 0870 606 1248

w t

o clean

CAUTION: To prevent damage to wood floors,

follow the flooring manufacturer’s cleaning

recommendations

NOTE:

If using cleaner on sealed wood floors, inspect

floor surface for worn finish, bare wood or separated

joints.

It is not recommended to use the cleaner on wood

floors if any of these conditions exist

Fill clean water tank according to instructions for Figs. 4/8

to 4/10.

Fill solution container with Vax Hard Floor Solution

according to instructions for Figs. 4/10 to 4/11.

Slide brush setting selector to

OFF.

Dry hands and

plug cleaner into a properly grounded

outlet.

Step on handle release pedal and lower handle to

operating position.

Set Wash/Rinse switch to

WASH. Turn cleaner ON.

To release solution, press trigger. Slowly move cleaner

forward and backward over area to be cleaned.

To pick up dirty solution, release trigger and slowly move

cleaner over area where solution has just been dispersed.

Use both forward and reverse strokes.

If rinsing the floor is desired, set Rinse Setting switch to

RINSE. This setting provides a water-only rinse in both the

forward and reverse strokes.

Rinsing is not necessary, but will help remove solution

residue from the floor.

Empty recovery tank when the motor sound becomes

higher pitched and there is a loss in suction (see

“Automatic shut-off”, Fig. 4/5).

When finished cleaning, follow “After cleaning”

instructions on page 10.

Unplug cleaner from electrical outlet and remove

squeegee from nozzle. Rinse it in clear water.

Picking Up Spills

Your Vax Dual V cleaner may also be used to pick up small

liquid spills on carpet, upholstery or hard floors.

For best results, pick up spills immediately by placing the

stair/upholstery nozzle just above the spill and suction up

any residue on top of the carpet. If the spill remains, place

either the stair/ upholstery nozzle or floor nozzle with the

brush setting selector to

OFF in front of the spill, pull the

nozzle very slowey over the spill initially with suction only.

Repeat with spray and suction.

When picking up spills on hard floors, use the carpet

cleaner with the hard floor tool in place (see “Cleaning hard

floors”, Figs. 5/5 & 5/6). Slide the brush setting selector to

OFF.

If a spot is left, the stair/upholstery nozzle is generally

more effective for removing it. Although no cleaning

solution can completely remove all spots, they can be

treated by following the instructions provided by the

manufacturer of the carpet, upholstery or hard floor

surface to be cleaned.

Do not use the Dual V cleaner to pick up flammable or

combustible liquids or chemicals.

When finished, follow “After cleaning” instructions.

Attach Hose

Unplug cleaner from electrical outlet

. Open hose

connection port (A) (Fig. 5/7).

Insert short hose end, matching tabs on hose with same-

sized slots in port. Push hose into port and lock in place

(Fig. 5/8).

Plug solution tube firmly into solution connection port (B)

(Fig. 5/9)

Fig.5/7

Fig.5/8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

VAX V-125 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info