Bedienungsanleitung VDO Dayton cd 1737 x (Seite 13 von 19) (Englisch)

163835

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

7. Short press: select Mono/

Stereo

Long press: select Local/

Distant Reception

11. Toggle sound equalization

14. Increase/decrease

volume

SECURITY

Removing the Front (fig. A and I)

1. Press the REL key, to flip-down the front.

2. Pull the front towards you. Follow the dia-

gram mounted on the back of the detachable

unit.

3. Take the detachable front with you when you

leave the car.

4. Keep the front in its protective cover.

Replacing the Front (Fig. K and L)

1. Take the front from its protective cover.

2. Insert the front into radio until it clicks into

position.

3. Close the front until it clicks into position.

Note 1:

If you hear a warning signal, the front is not

properly replaced!

Note 2:

To ensure good connection between the set

and the detachable unit, it is advisable to clean

frequently the connections with a cotton swab

from time to time!

Note 3:

Do not touch the electrical contacts when re-

moving or replacing the front panel!

GENERAL OPERATION

Switching On/Off

Press button to switch the set on or off.

Setting the Start-up Volume

1. Long press the VOL/SEL knob to enter the

special functions mode.

2. Press the knob till you see "IN VOL XX", where

"XX" is the starting volume.

3. Turn the knob to adjust the IN VOL to a com-

fortable level.

Note: If the radio was previously at a higher

volume level when you turned off the radio:

After you turn on the radio, the radio will use

the starting volume. Otherwise the radio will

remember the previous volume level.

Selecting a Source

Your car radio is designed for different types

of sources.

z RADIO

z CD

z USB

z SD/MMC

z AUX

Press the MODE button to select the source.

Sound Controls

Volume

Please make sure you can still hear the traffic

(horns, sirens..….)

z Turn the volume knob to adjust the volume.

Note: You can adjust the start-up volume (IN

VOL). When the start-up volume is set to maxi-

mum level, it may be extremely loud when you

switch on the set.

See: Setting the Start-up Volume

Balance

To change the balance between the amount of

sound output on the left and right side.

1. Press the VOL/SEL knob to select the sound

control Balance (BAL).

2. Turn the knob to adjust the level of sound

output to the left and right speakers.

Bass (only when DSP is off)

To change the enhancement of low frequency.

1. Press the VOL/SEL knob to select the sound

control Bass (BAS).

2. Turn the knob to adjust the level of bass en-

hancement.

Treble (only when DSP is off)

To change the enhancement of high frequency.

1. Press the VOL/SEL knob to select the sound

control Treble (TRE).

2. Turn the knob to adjust the amount of treble

enhancement.

Fader

To change the amount of sound output to the

front and rear speakers.

1. Press the VOL/SEL knob to select the sound

control Fader (FAD).

2. Turn the knob to adjust the level of sound

output to the front and rear speakers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

VDO Dayton cd 1737 x Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von VDO Dayton cd 1737 x

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info