Bedienungsanleitung VDO Dayton CD1107 (Seite 10 von 18) (Englisch)

98458

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Connecting 4 loudspeakers

Side & pol. Front/colour Pin Rear/colour Pin

Left (+) Green [B5] White [B7]

Left (-) Green/black [B6] White/black [B8]

Right (+) Grey [B3] Blue [B1]

Right (-) Grey/black [B4] Blue/black [B2]

) For this accessory, contact your dealer.

Line out

You can connect a power amplifier with 2 or 4

additional loudspeakers to this set using the

labelled RCA cable.

z Red socket to right channel

z White socket to left channel.

Audio In

You can connect external audio equipment via

the labelled AUX-in RCA cables.

z Red wire for Right Channel input

z White wire for Left Channel input.

MOUNTING

Metal Sleeve (fig. F and G )

Install the metal sleeve in the dashboard. For

optimal performance of the CD player, the metal

sleeve should be positioned horizontally (be-

tween -10° and +30°).

Fix metal sleeve into place by pressing the metal

tags outwards using a screwdriver.

Connecting the Radio (fig. C)

z Ensure the battery is disconnected.

z Insert power supply connector A’ into socket

z Insert loudspeaker connector B’ into socket

z (Optional) Insert the line-out connector into

the corresponding socket.

z (Optional) Insert the AUX connector into the

corresponding socket.

z Insert aerial plug into the aerial socket (good

reception is only possible with a good aerial).

If an antenna adaptor is needed, please con-

sult your dealer.

Mounting the Radio (fig. G and H)

This radio can be properly installed either from

conventional Front Mounting and/or from Rear

Mounting.

Front Mounting

z Slide the radio into the metal sleeve until the

springs at either side of the radio snap into

the openings of the sleeve.

z Finally reconnect the negative car battery

terminal.

Rear Mounting

z Choose a position where the screw holes of

the mounting bracket and the screw holes of

the radio become aligned and tighten the

screws at 2 places on each side.

z Only use M5 screws that are not longer than

6 mm.

Removing the Radio (using the two

removal keys supplied) (fig. J)

z Press the REL button and open the front

panel.

z Insert both removal keys into the holes on the

front of the set until they lock.

z Pull out the radio.

Replacing the Fuse (fig. C)

z Replace with a 15A blade-type fuse.

The new fuse must be of exactly this value

and type otherwise the set will not be ad-

equately protected. Ignoring this procedure

may lead to damage to the set, which will

invalidate the guarantee.

Interference Suppression

z Most modern cars have sufficient interference

suppression. If you experience interference

generated by the car, consult your dealer.

FRONT PANEL AND REMOTE

CONTROL

See fig. A and E.

Front Panel and Remote Control

Function(s)

1. 1. Switch On / Off the set

2. Press to fold down the front

panel

3. 11. Radio:

Short press: auto-seek a

station (auto mode)/stop

the frequency (manual

mode)

Long press: activate

manual tuning mode

CD:

Short press: select the

previous or next track/

file

Long press: Review/

Fast-forward the current

track

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

VDO Dayton CD1107 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von VDO Dayton CD1107

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info