Bedienungsanleitung VDO X10W (Seite 14 von 39) (Deutsch, Englisch, Französisch, Italienisch)

483657

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

X1 VDO CYCLECOMPUTING26

F I

I F

www.vdocyclecomputing.com X1 27

DGBD GB

4 Installation

4.1 Fitting the sensor, magnet and handlebar holder >>> P01

When ﬁtting to suspension forks, it is essential

to bear in mind the spring deﬂection of the

forks. The cable requires an appropriate amount

of play.

ATTENTION: Risk of broken cable.

Step 1 Place the rubber pad under the sensor.

Fit the sensor on the same side of the fork where

you later want to ﬁt the computer to the handle-

bars (right or left) using the cable ties supplied

(loose at ﬁrst, do not pull tight just yet).

Depending on the room available, the sensor can

be ﬁtted at the front of the fork, inner side of the

fork or backside of the forks. >>> P02

Step 2 Place spoke magnet around an outer

spoke. The silver middle of the magnet points

towards the sensor. Align the magnet to the

sensor mark with a gap of about 1 - 5 mm.

Step 3 Align sensor and magnet for good and

fasten in place: Pull cable ties tight and push

magnet in ﬁrmly.

Step 4 Install cable from sensor already ﬁtted

along brake cable to the handlebars (fasten with

cable ties supplied) Ideally: Coil sensor cable up

around the brake cable.

Step 5 Decide whether ﬁtting to handlebar or

stem and turn the base of the handlebar holder

by 90° accordingly. To do so, undo the screws in

the holder, take out the foot and turn it 90°, in-

sert and tighten the screws again.

ATTENTION: Do not over tighten screws.

Step 6 Guide the cable ties through the slot in

the handlebar holder, place around the handle

bars or the stem and pull (do not pull tight just

yet).

Step 7 If ﬁtting to handlebars: Align computer

angle to achieve optimum readability. Now pull

cable ties tight. Snip off protruding ends with

clippers.

4.2 Installing the battery in the computer >>> P03

Your VDO computer is supplied with a 3V battery

(type 2032). The battery is already installed

when supplied. To change the battery, proceed

as follows:

step 1 Place the battery in the computer casing

with the +terminal facing up.

Step 2 Make sure that the battery does not

get wedged.

step 3 Take care that the rubber seal lies ﬂat on

the battery compartment lid.

Step 4 Insert the battery compartment lid into the

opening and turn it with a coin to the right as far

as it will go (approx. 1/3 turn).

TIP for changing battery: VDO recommends chang-

ing the battery once a year. Buy a new battery in

good time to ensure the function works perfectly.

When the battery is changed, all basic compu-

ter settings are reset to factory settings. Before

removing the old battery, it is therefore essential

to note down the wheel sizes entered and the

total kilometres cycled so far for your bike 1 and

bike 2. Program these in again after inserting the

new battery.

4.4 Placing the computer into the handlebar holder >>> P04

The VDO twist-click system fastens the computer

securely with the handlebar holder.

Step 1 Place computer into the holder in 10 o’clock

position.

Step 2 Twist computer to the right to 12 o’clock posi-

tion and click into the holder system.

Step 3 To take the computer out, twist to the left

(do not push or pull).

How to remember: Rigid to the Right, Loose to the Left

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

VDO X10W Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von VDO X10W

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info