Bedienungsanleitung Velbon ULTRA REXi L-A (Seite 1 von 2) (Englisch)

540835

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

7.Leg Length Adjustment

5.Lower column

2.Fixing bolts for the head

3.Elevator

4-1.Leg Angle Adjustment 4-2.Leg Angle Adjustment 4-3.Leg Angle Adjustment

Head Screw of ULTRA REXi L is interchange-

able. Normally 1/4 inch has been set when

shipped out from the factory.

However it is possible to change the size of the

screw by changing direction to 3/8 inch. In order

to remove the 1/4 inch screw, please use the

wrench which is included in the package and

rotate the Hexagonal Nut, then remove the screw

and insert upside down, then set the hexagonal

nut back for locking firmly.

While legs are closed position, slide the Leg

Angle Adjusting Knob to right until feeling the

click to stop.

Open the legs to obtain the low position. The

Elevator can be split by rotating lower column to

detach.

In case opening the legs unexpectedly, push

the Cancel Button to set back to the original

angle.

After opening the legs fully, set back leg angle

slowly to be located at the Semi-Low angle with

the Click sound.

Closing the legs further until the leg angle

becomes standard with a click sound.

After detaching the Lower Column, remove the

Center End and screw in the end of the upper

column. Do not lose the Lower Column after that.

Holding the Leg Top Rubber tightly and rotating

to Unlock direction with feeling 4 clicks which

means each leg section becomes loosen.

Extending the legs till the end, then twisting to

the Lock direction firmly. For folding back the

legs, please do opposite way.

Use the second locking part which is covered

with foam grip in order to shorten the length after

fully extending the legs. Rotate to the Second

locking part to the unlocking direction while

pushing down to shorten or pulling up to extend

for the adjustment the length. After reaching to

the desired length, twisting to the Lock direction

with even stronger tension.

In the package, there are bolts for fixing the head

on the Pedestal firmly as additional parts.

Insert the bolts from the bottom side of the

Pedestal and making sure to touch the bottom of

the Panhead safely.

There are several sizes of the bolts to fit

with any type of the length of the Pedestal

and Camera mounting screw.

The bolts may skratch the bottom of the

head due to its function as well as

construction.

While sliding down the locking plate, raise up the

EV Locking Lever, then the Elevator becomes

unlock. Up or down the Elevator to desired height

and push down the EV Locking Lever to lock. EV

Locking Lever can be tighten or loosen by

turning the adjusting bolt with a hexagonal

wrench which is included in the package.

Make sure holding your camera while

operating the Elevator.

1.Head screw for the tripod

＜For ULTRA REXi L(A) only＞＜For ULTRA REXi L(A) only＞

6.Legs extension and lock

ULTRA REXi L(A) ULTRA VOXi L(A)

OPERATING MANUAL

※

Leg Top Rubber may be dirty after use on the ground. Please be careful it may cause your cloths or your

hand. Watch your finger which may not be bound while extending or folding the legs. Before installing

the Camera on the tripod, please make sure the strength of the leg locking by pushing from the above of

the tripod. After checking that any leg does not collapse, please put your camera on the tripod.

UNC 1/4 inch UNC 3/8 inch

Hexagonal Nut

Pedestal

Bolt

Slide

down

Locking

Plate

EV Locking

Lever

Raise up

Up and Down

Adjusting Bolt

Leg Angle

Adjusting Knob

Cancel Button

Open

Split

Leg Angle Adjusting Knob

returns automatically to left.

Leg Angle Adjusting Knob

returns automatically to left.

Click

Closing

Lower column

(Detached elevator lower section)

Standard Leg Angle

Screw in

Lower Column

Center End

Detach

Leg Top Rubber

Lock

Unlock

Feeling 4 clicks at

each section of the legs

Extending along with

the groove till the end

HS Imaging GmbH

Alte Landstraße 26

51647 Gummersbach

verkauf@hs-imaging.de

www.hs-imaging.de

Telefon (02263) 90 231 41

Telefax (02263) 90 231 46

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Velbon ULTRA REXi L-A Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info