Bedienungsanleitung Velleman HAM982K (Seite 2 von 52) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

585216

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

HAM982K 2 VELLEMAN

1M 2M 3M 4M 5M 6M 7M 8M 9M 10M 11M 12M

42.1░

-42.1

3. PIR Detector

a. Technical Specifications

Detection element low noise dual element pyro sensor

Operating voltage 8-16Vdc ; 12Vdc nominal

Current consumption typical 15mA at 12Vdc

Power-up delay typical 2 minutes with flashing LED indication

Alarm period 2-3s

Alarm output N.C. relay contact with 10Ω in-line resistor. Contact rating: 28Vdc, 0.1A

Walk test with LED alarm indicator

Pulse counting Normal response or 2 pulses within 12 seconds for "harsh" environments

Tamper switch N.C. contact with 10Ω in-line resistor. Contact rating: 12Vdc, 50mA

Operating temperature -10 to +55°C

Humidity max 95% non-condensing

EMC conform to CE standard

Dimensions (HxWxD) 116 x 73.5 x 74mm

b. PCB layout

1. Pyro-sensor (do not touch this sensor!)

2. Walk test & alarm indicator

3. Tamper switch

4. Pulse count jumper ("harsh": for environment with high risk of false detection)

5. LED on/off jumper (on = flashing during start-up, on during operation)

6. Connection terminal block:

Tamper: if a tamper switch is required, connect these terminals to a 24h

normally closed (NC) zone in the alarm control panel. Opening the

housing will trigger a tamper signal.

12Vdc: connect (+) to an 8-16V power source, usually from the alarm control

panel. Connect (-) to the common grounding point.

Alarm: the alarm output relay of the detector. Connect these terminals to a

normally closed (NC) zone in the alarm control panel.

c. Installation

• Install the detector indoors, on a stable surface with a clear view on the protection area.

• Avoid mounting where hot or cold air may blow directly onto the device and where objects

in the detection field may change temperature rapidly (heating or air-conditioning devices).

• Considering the detection angle of the device (see figure on the right), corner mounting is

recommended, at a height of 2 to 3 meters.

Procedure:

1. Open the cover by inserting a small screw driver into the edge of the unit and turning it to release the cover.

2. Remove the PCB by releasing the two fixing screws from the support post - DO NOT DROP THE PCB!

3. Numerous "knockouts" are provided on the back plate. Punch the one which will provide the best cable entry.

4. The two fixing holes on the back of the back plate are for surface mounting. The two fixing holes on the left and

right of the back plate are for corner mounting. Fix the back plate firmly on the wall with the two enclosed screws.

5. Put the PCB back onto the back plate and fix it firmly. Connect the wires to the terminal block.

6. Clip the front cover back in place on the back plate. See to it that the tamper switch is depressed when the front

cover is in place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Velleman HAM982K Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info