Bedienungsanleitung Velleman HAM982K (Seite 5 von 52) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

585216

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

HAM982K 5 VELLEMAN

8 Common ground

9 This terminal provides +12V output power upon alarm condition during the time period set in the alarm timer. It

is ideal for a siren or alarm bell. The output is equipped with a 2.5A resettable fuse.

10-13 These terminals are the connection points for remote switches for arm-disarm control (optional). These

switches need to be of the 'momentary contact' type and equipped with 2 LEDs (home/away LED and status

LED). Up to 3 of these switches can be connected in parallel. Switches that can be used are HAA80 (key

switch), HAA85 (security keypad) and HAA85WP (security keypad – waterproof).

10: to connect the actual key switch contact(s)

11: to connect the home/away LED(s): away= all zones are activated ; home= only the selected zones are

activated (see "8.l.Setting "HOME" mode") – the other zones are freely accessible.

12: to connect the status LED(s)

13: +12V common point for contacts and LEDs, equipped with a 750mA resettable fuse.

switch contact status results

ARMING THE SYSTEM

contact away mode arming

• Exit delay starts

• Exit beep sounds if it is enabled

• The system will be armed after exit delay

contact home mode arming

• The 2

touch must be made within the exit delay period

• Exit beep sounds continuously during exit delay

• The system will be armed after exit delay

DISARMING THE SYSTEM

contact system disarmed

• The system is disarmed and reset if there was no

alarm. It is ready for rearming.

• The system is disarmed but with alarm memory if an

alarm occurred – 2

contact is required

contact

• alarm memory is cleared

• system remains disarmed

The alarm memory LEDs are off ('status' LED + zone

LEDS). The system is ready for rearming.

LED on off flashing

home-away away mode system disarmed home mode

status

• exit delay starts but there

is/are (an) unsealed zone(s)

– check zone connections

• system is armed after exit

delay expired

system disarmed

• Flashing slow: exit delay starts and

the zones are normal

• Flashing fast: zone is or was in alarm

• Flashing fast with intervals: system is

disarmed or zone with alarm memory.

14-16 These terminals have no function.

17-28 These terminals are protection zones 1-8 and their common ground

terminals. The zones are EOL (End of Line), with a 2.2kΩ resistor.

NC (normally closed) contacts are to be wired in series with the EOL

resistor, whereas NO (normally open) contacts are to be wired in parallel with the EOL resistor. The function of

the zones and their response times are programmable via the system programming options.

17=zone 1 ; 19=zone 2 ; 20=zone 3 ; 22=zone 4 ; 23=zone 5 ; 25=zone 6 ; 26=zone 7 ; 28=zone 8.

18, 21, 24, 27: common ground.

IMPORTANT: the cabinet's (NC) tamper switch is pre-wired to zone 8 internally. We suggest you always keep

zone 8 as a 24h protection zone.

DAP jumper: DAP means Direct Access to Programming: this jumper is provided to set the system in programming

mode in case the master code is forgotten or lost.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Velleman HAM982K Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info