Bedienungsanleitung Velleman WS1060 (Seite 10 von 77) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch, Polnisch)

622070

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

WS1060

V. 02 – 26/04/2013 10 ©Velleman nv

4. Press + repeatedly to display the minimum values for: outdoor humidity, outdoor temperature, wind chill

temperature, dew point, indoor humidity, indoor temperature.

5. Press HISTORY to return to normal mode.

Resetting a minimum or maximum

To reset a minimum or maximum:

1. Enter minimum or maximum reading mode and press + to display the value that you want to reset.

2. Press and hold SET for 3 seconds.

3. Repeat for any other minimum or maximum value that you want to reset.

4. Press HISTORY to return to normal mode.

8. Resetting

To reset the weather station to the factory defaults, press and hold the + key for 20 seconds.

9. Troubleshooting

Problem

Possible Cause

Solution

Transmission problem

Distance between the two units is too long

Reduce distance

Shielding materials between two units

(thick wall, steel…)

Find a different mounting location

Interference from other sources

Eliminate interference sources

Data on LCD is

illegible

No data reception

Find a different mounting location

Low batteries

Replace batteries

Incorrect data

Low batteries

Replace batteries

Incorrect settings

Reprogram the weather station

10. Calibration

For accurate measurements, you can calibrate wind speed, temperature, humidity, and rainfall measurements

using calibration tools (not incl.).

To enter calibration mode, proceed as follows:

1. From normal mode, press and hold HISTORY for 8 seconds.

The station is now in calibration mode. The wind factor digits on the display flash.

2. Press SET to go to the next setting; use the + or MIN/MAX keys to change the values.

3. To exit the calibration mode, press HISTORY.

See below for a description of each calibration setting.

Wind speed calibration

The default wind speed calibration setting is 1.0. The adjustment factor ranges from 0.75 to 1.25. You can set it

in 0.01 increments.

Wind speed is the most sensitive to installation constraints. The following factors influence wind speed

measurement:

 the location of the weather station: proximity of buildings, trees, or other obstructions

 the wear of the moving parts of the anemometer.

To calibrate the wind speed, we recommend using a calibrated wind meter (not incl.) and a constant-speed,

high-speed fan (not incl.).

Temperature calibration

You can calibrate indoor and outdoor temperature measurements.

The following factors influence temperature measurement:

 proximity of heat sources, such as buildings, the ground…

 installation in direct sunlight without proper shielding in hot weather environments.

To calibrate the temperature, we recommend using a mercury or alcohol thermometer (not incl.). Do not use

bi-metal (dial) or other digital thermometers, as they have their own error margin. Do not use a local weather

station in your area (difference in location, timing of updates, and possible calibration errors).

To calibrate the temperature, proceed as follows:

1. Place the temperature sensor in a shaded, controlled environment.

2. Place the thermometer right next to it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Velleman WS1060 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info