Bedienungsanleitung Velleman WS2801 (Seite 7 von 29) (Englisch)

622074

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

3. Insert two "C" size batteries into the thermo-hygro sensor with the correct polarity.

4. Insert two "C" size batteries into the wireless display with the correct polarity.

NOTE: Every time the wireless display receives data from the sensors, the

wireless icons will blink once and then return to solid if the last transmission

was successful. A wind speed or rainfall amount that reads "0" does not mean

reception failure, it means that there was no wind or rain at the time of the last

measurement. The thermo-hygro sensor syncs with the wind and rain sensors

and sends all outdoor sensor data to the display. The thermo-hygro sensor tries

for 7 minutes to sync to the wind sensor and for the rain sensor. If not successful

within 7 minutes, the thermo-hygro sensor will stop looking for the other sensors.

5. Setup troubleshooting: If the sensor data fails to display for any of the outdoor

sensors within 10 minutes, (“- - -“ is displayed), remove the batteries from all

units (except for the Wind Sensor) for 1 minute and start the Setup procedure

again at Step 1 and completely reset the solar Rain Sensor (see Step 2:

Important).

ADDITIONAL NOTES FOR THE SOLAR WIND AND RAIN SENSORS MODES:

IDLE MODE

This mode aims to reduce the power consumption of the transmitter. Under this mode,

the sensor stops the transmission of signal, checks the battery voltage and detects the

solar cell condition. The IDLE mode happens if the battery voltage is low.

Note: The sensor will check and charge up the rechargeable battery automatically.

When it detects that the battery voltage is sufficiently charged up and high enough, the

transmission of signal starts again.

STOP MODE

It is the most energy saving mode. Under this mode, the transmitter stops the

transmission of signal. There is no checking of the battery voltage and no detection of

the solar cell condition. The STOP mode happens:

• If the user covers the solar cell for 10 seconds and presses the RESET

button (Wind Sensor).

• If the sensor(s) is (are) placed in the dark environment for 72 hours.

Note:

• To restart the Solar Wind Sensor after placing it in the dark environment for

72 hours, user should place the sensor in a bright environment then spin the

wind cups, or press the RESET button once to wake it up again.

• If the Solar Wind Sensor is stopped by pressed the RESET button, user

must press the RESET button once to wake it up again.

• To restart the Solar Rain Sensor, should swing the seesaw or, follow the

SETTING UP, Step 2: Important instructions to completely reset the sensor.

IMPORTANT! During the restart process, if the battery voltage is high enough, the

transmission of signal starts again. However, if the battery voltage is low, the sensor(s)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Velleman WS2801 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Velleman WS2801

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info