Bedienungsanleitung Velodyne Impact-10 (Seite 8 von 20) (Englisch)

567716

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

www.velodyne.com

2 - Impact Series User’s Manual

Placement

The rst step in installing your new Impact sub is to determine where it will be placed in the room. Unpack the

system carefully and use the following guidelines in order to nd the best room placement option.

True subwoofers operate at extremely low frequencies which are primarily omni-directional. Keep in mind that

frequency response and output level can be drastically inuenced by placement, depending on the acoustic

properties of the listening room. To obtain optimum output from your subwoofer, try placing it within a foot of a

corner. This location will oer the greatest output levels and optimum low frequency extension. If at all possible,

your subwoofer should be placed along a wall. The worst location for a subwoofer is typically far away from any

walls and close to the center of your room. Avoid these locations when possible. When using a pair of Velodyne

subwoofers in 2-channel stereo, it is preferable to feed each subwoofer with one channel and place each

subwoofer near the satellite of the same channel.

Depending on the size and type of furnishings in the room, perfect placement may not be possible. Finding the

best location within your environment will likely require some experimentation. We suggest you experiment with

the location during setup to nd what sounds best to you when seated in your typical listening position.

Regardless of where you install your Velodyne subwoofer, it must remain in an upright position. Using, shipping

or storing the subwoofer in any other position for an extended period of time may result in damage to the unit

not covered by warranty.

Caution!

This subwoofer has electronics built into the cabinet. Do not place the cabinet next to sources of heat such as

furnace registers, radiators, etc. Do not place the unit near sources of excessive moisture, such as evaporative

coolers, humidiers, etc. The power cord should be routed in such a way that it will not be walked on, pinched

or compressed in any way that could result in damaging the insulation or wire.

Your Velodyne Impact subwoofer is NOT magnetically shielded. Should you nd it necessary to use it with an

older CRT monitor or TV, keep it at least two feet from the monitor. Experiment for correct distance by minimizing

distortion of the picture and colors.

INSTALLATION

Inputs

Your new subwoofer is equipped with speaker-level and line-level inputs. Use the LINE LEVEL jacks when

connecting your subwoofer to a pre-amp, signal processor (such as LFE out), linelevel crossover, or receiver

with pre-amp level outputs. When using the line level jacks, some receivers may not provide enough signal to

have the unit’s auto-on feature operate properly. Additionally, this lack of signal may also cause the subwoofer

to produce less output than it is capable of.to produce less output than it is capable of.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Velodyne Impact-10 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info