Bedienungsanleitung Velodyne MiniVee (Seite 9 von 20) (Englisch)

567719

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

www.velodyne.com

MiniVee User’s Manual - 3

INSTALLATION

Inputs

Your new subwoofer is equipped with speaker-level and line-level inputs. Use the LINE LEVEL jacks when

connecting your subwoofer to a pre-amp, signal processor, line-level crossover or receiver with pre-amp level

outputs.TheSPEAKERLEVELjacksconnectdirectlytothespeakeroutputsofanyamplier,integratedamplier

orreceiver.Yourampliersectionwillnoticenoadditionalloadingeectswhenyouusetheseinputsduetotheir

very high impedance.

Important!!!

Do not use both LINE LEVEL and SPEAKER LEVEL connections simultaneously!

Volume Control

Thiscontrolallowsyoutobalancetheoutputfromthesubwoofertothemainspeakers/amplierinyoursystem.

This control should be set to achieve similar output level from both the main speakers and subwoofer when

listening to music. A good starting point for the volume control is 3 or 4 dots from minimum.

Low-pass Crossover - 40 to 120 Hz

All inputs sum the left and right channels together, with the resulting signal passing through an adjustable

low-passcrossoverbeforebeingamplied.Thecrossovercontrolallowsyoutoadjusttheupperlimitofthe

subwoofer’sfrequencyresponsefrom40to120Hz.Thesubwoofer’sresponsewillbeginrollingoabovethe

frequency you set this control to. You should set the crossover frequency to obtain a smooth and seamless

transition from the subwoofer to the main speakers in your system. If your main speakers are smaller units with

limitedlowfrequencyoutput,youmaywishtochooseahigherfrequency(suchas100-120Hz)thanyouwould

with larger speakers which have greater low frequency output. With larger speakers, you might start with this

controlsetlower,suchas80Hz.

Abypassswitchisalsoprovidedifyouwishtouseanexternalcrossover.If you are not using an external

crossover, we recommend that you use the one provided within the unit for optimum performance!

Phase Adjustment - 0°/180°

Thiscontrolallowsyouto“reverse”thephaseofthesubwoofer’soutputsignal180°tocorrectforanypossible

mismatchandresultingcancellationbetweenthesubwooferandyourmainspeakers/amplier.Toadjust,simply

listen to the system with music playing. Then move the switch from one position to the other and listen for a

change in low frequency output. The correct position will have a greater amount of apparent low frequency

output.

Crossover Switch - INTERNAL X-OVER/SUBWOOFER DIRECT

This switch allows the internal crossover circuitry to be removed from the signal path. This is required in certain

installationswhichroutethesignalthroughexternalprocessorswithacrossovercircuitoftheirown,suchasthe

new digital units. Simply move the switch to SUBWOOFER DIRECT todisengagethebuilt-incrossover.Forall

other installations which do not have a separate electronic crossover, we recommend you leave the switch set

to INTERNAL X-OVER to provide optimum performance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Velodyne MiniVee Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info