Bedienungsanleitung Velodyne Optimum-12 (Seite 9 von 28) (Englisch)

567740

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

www.velodyne.com

Optimum Series User’s Manual - 3

INSTALLATION

Inputs

Your new subwoofer is equipped with speaker-level and line-level inputs. Use the LINE LEVEL jacks when

connecting your subwoofer to a pre-amp, signal processor (such as LFE out), linelevel crossover, or receiver

with pre-amp level outputs. When using the line level jacks, some receivers may not provide enough signal to

have the unit’s auto-on feature operate properly. Additionally, this lack of signal may also cause the subwoofer

to produce less output than it is capable of.

To alleviate this condition, we recommend the following steps:

1) If using line level jacks, BOTH THE LEFT AND RIGHT INPUT SHOULD ALWAYS BE USED – never use

just the left or just the right input. If using line level connections from a preamp or signal processor, use

both Left and Right inputs from your preprocessor or preamp and connect them to the Left and Right

inputs on your subwoofer.

2) If using a receiver with LFE out, be sure the LFE channel is sending adequate signal to the subwoofer. The

subwoofer’s default volume setting is 30 on a 1-80 scale (roughly 1/3 volume). Adjust the LFE channel on

your receiver or processor to achieve the desired bass output. See your receiver or processor’s owner’s

manual for more information.

Volume Control

This control allows you to balance the output from the subwoofer to the main speakers in your system. This

control should be set to achieve similar output levels from both the main speakers and subwoofer when listening

to music. The default volume setting is 30 on a 1-80 scale.

Warning:

Some manufacturers preset their receivers with the Sub-Out channel signal at a minimum level. It is very important

to verify that your receiver Sub-Out channel is set to the same output level as your front right and left channels.

Refer to your receiver manual for the individual channel level adjustment procedure. If your receiver Sub-Out

channel is set too low, the subwoofer may appear to have a weak output, it may sound noisy or distorted, and

the Auto On/Off feature may not operate properly.

Low-pass Crossover - 40 to 135 Hz

All inputs sum the left and right channels together, with the resulting signal passing through an adjustable

low-pass crossover before being amplied. The crossover control allows you to adjust the upper limit of the

subwoofer’s frequency response from 40 to 135 Hz. The subwoofer’s response will begin rolling o above the

frequency you set this control to. You should set the crossover frequency to obtain a smooth and seamless

transition from the subwoofer to the main speakers in your system. If your main speakers are smaller with limited

low frequency output, you may wish to choose a higher frequency (such as 100 - 120 Hz) than you would with

larger speakers which have greater low frequency output. The default crossover setting is 80 Hz. With larger

speakers, you may want to set this even lower, for example 70 Hz.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Velodyne Optimum-12 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Velodyne Optimum-12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info