Bedienungsanleitung Venga VG MGR 1 (Seite 11 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

488140

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Copies of the I/B. Please reproduce them without any changes except

under special instruction from Team International BELGIUM. The page

must be reproduced and folded in order to obtain a booklet A5 (+/-

148.5 mm width x 210 mm height). The page must be folded in order to

keep the good numbering when you turn the page of the I/B. Don’t

change the page numbering. Keep the language integrity.

11 VG MGR 1 - 101213



IMPORTANT INFORMATION

This appliance is not intended for professional use. You should follow the requested breaks.

Failure to follow this instruction carefully may result in damage to the motor. Please refer to the

rating label for the maximum continuous usage time (KB xx min where xx is the maximum usage

time). The breaks should last at least 10 minutes.

BEFORE THE FIRST USE

Check that the voltage indicated on the rating label corresponds to the mains voltage in your

home.

Wash all parts (except the body) in warm soapy water.

Before plugging in, ensure the “ON/OFF/Reverse” switch is turned to the "OFF" position.

INSTRUCTIONS FOR USE (see page 5)

ASSEMBLING

Hold the head and insert it into the inlet with one hand (fig. 1), place the locking knob into the

hole on the side of the motor housing with the other hand, and tighten it clockwise to secure the

head (fig. 2).

Place the feed screw into the head, long end first, by turning the feed screw slightly until it is set

into the motor housing (fig. 3).

Place the cutting blade onto the feed screw shaft with the blade facing the front as illustrated

(fig. 4). If it is not fitted properly, meat will not be ground.

Place the desired cutting plate next to the cutting blade, fitting protrusions in the slots (fig. 5).

Support or press the centre of the cutting plate with one finger, then screw the fixing ring until

tight with the other hand (fig. 6). Do not overtighten.

Place the hopper plate on the head and fix into position.

Locate the unit on a firm place.

The air passage at the bottom and the side of the motor housing should be kept free and not

blocked.

MINCING MEAT

Cut all foods into pieces (sinewless, boneless and fatless meat is recommended, approximate

size: 20 mm x 20 mm x 60 mm) so that they fit easily into the hopper opening.

Plug in and turn the “R / ON” switch to "ON" position, then turn the “ON/OFF/Reverse” switch to

"ON" position.

Feed foods into the hopper plate. Use only the food pusher (fig. 7).

After use, switch the unit off and unplug it from the power supply.

REVERSE FUNCTION

In case of jamming, switch the appliance off by turning the “R / ON” switch to

"R" position and the “ON/OFF/Reverse” switch to "R" position.

The feed screw will be rotating in the opposite direction, and the head will get empty.

If it doesn't work, switch the unit off and clean it.

Assembly page 11/44

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Venga VG MGR 1 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info