Bedienungsanleitung Venga VG VC 4 (Seite 9 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

488178

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced and

folded in order to obtain a booklet A5 (+/- 148.5 mm width x

210 mm height). When folding, make sure you keep the good

numbering when you turn the pages of the I/B. Don’t change

the page numbering. Keep the language integrity.

Fax +32 2 359 95 50

ASSEMBLING THE VACUUM CLEANER

Always remove the plug from the power socket before fitting or removing accessories! •

•

Insert the hose connector into the hose connection inlet until it locks. To remove the hose,

press the sides of the hose connector and pull at the hose.

Fit the tube to the handle.

Fit the tube to the floor brush.

You can adjust the length of the tube.

Removing tube and accessories: to remove the accessories, pull firmly apart.

The floor brush is ideal for the daily cleaning of carpets and hard floors.

Setting with the bristles inside for cleaning carpets.

Setting with the bristles outside for cleaning hard floors.

• The appliance is delivered with the following accessories:

 a crevice tool: for radiators, crevices, corners, baseboards

and between cushions.

 an upholstery brush: for curtains, cushions, edges, doors,

mattresses etc.

OPERATION

Pull out a sufficient length of power cord and insert the plug into the power socket. A

yellow mark on the power cable shows the ideal cable length. Do not extend the cable

beyond the red mark. Switch on the appliance by pressing the ON/OFF switch with your

foot.

You can adjust the suction power by using the wind-force adjuster on the handle of the

flexible hose. Use a low suction power for furniture and other delicate surfaces and use

high suction power for fitted carpet and other floors.

AFTER USE

Stop the vacuum cleaner by pressing the ON/OFF switch.

Unplug the appliance from the power supply.

Simply press the cable rewind button to activate the cable rewind mechanism.

The carrying handle can be used to move the appliance. Never use the handle of the

dust container to carry the appliance!

After use we advise you to empty the dust collector to avoid smells and mildew that could

be caused by damp dust particles that may have been vacuumed, and also to

guarantee an optimal efficiency during the next use. To do so, see below.

EMPTYING THE DUST COLLECTOR

• Press the release button of the dust container and pull the dust container out.

• Hold the dust collector over a dustbin, press the unlocking button at the bottom of the

handle of the dust collector to open the lower cover of the dust container and spill the

rubbish.

• Close the dust collector and put the dust collector back in the appliance until it locks in

place.

9 VG VC 4 - 101220

Assembly page 9/44

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Venga VG VC 4 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info