Bedienungsanleitung Ventus W164 (Seite 8 von 13) (Deutsch, Englisch, Dänisch)

556666

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

- Single press [0] button. The reading will reset to zero and the “TARE” icon will remain on the upper display.

Now you can add your additional ingredient. Only the weight or volume of the last ingredient added in measured. Continue

above procedure to build up different ingredients for your recipe.

NOTE: The tare function only operate when the cup is placed on a flat surface

Reversing the Tare Function

Right after the tare function has been performed and the display is showing “0” reading with the “TARE” icon appeared, you

can press [0] button to resume the original weight or volume reading just before the tare function and the “TARE” icon will

disappear.

NOTE: The reverse tare function only operate when the cup is placed on a flat surface

IMPORTANT NOTE

: It is easy and convenient to mix different ingredients in the cup. However when mixing your ingredients,

you should avoid pressing down the bottom of the base where the sensitive weight scale components are located.

Excessive force applied to the base of the cup may permanently damage the scale inside and provide inaccurate reading.

FAULT MESSAGE DISPLAY

UnSt: Unstable

The scale is unstable and the unit will turn off automatically. Place the cup on a flat table and

turn on the unit again by pressing [0] button once.

Err: Error

The scale is overloaded. The weight or volume in the cup exceeds the maximum display

range (refer “Specification” section)

CALIBRATION

To ensure accurate measurement, you are suggested to check the weight of an empty cup every time you first turn on the

unit. It should read 0 gram (or oz) for your empty cup.

Calibration for the cup is needed ONLY when the reading of your EMPTY cup is higher than zero (gram, oz, cups, fl oz or

ml). The calibration process will reset the reading to zero for the empty cup.

To calibrate,

1) Make sure the transparent cup is attached to the base.

2) Make sure the cup is empty. Clean the unit with a dry cloth to remove any excess liquid on the cup.

3) Turn on the unit by a single press of the [0] button.

4) Make sure the cup is placed steadily on a flat surface. Hold [0] for 6 seconds until “CAL” flashes. Do not touch or move

the cup when “CAL” is flashing.

The display reading will show “0” and the calibration is completed

CLEANING AND STORAGE

- The transparent cup is dishwasher safe and it is detachable for cleaning. Press the button below the handle to unlock

and detach the cup from the base

- Only clean the transparent cup with cold or warm water together with optional mild cleaning detergent. Do not use

boiling water to clean the transparent cup as it can withstand up to 70C maximum.

- Detach the transparent cup and use damp cloth to clean the base and the handle.

- Never immerse the base & handle in water or put into dish washing machine for cleaning

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ventus W164 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info