Bedienungsanleitung Verizon FiOS 9100EM (Seite 15 von 211) (Englisch)

629193

Zoom out

Zoom in

Vorherige Seite

1/211

Nächste Seite

030-300554 Rev. A 14 June 2008

Verizon FiOS Router

(

Model 9100EM

)

User Guide

5.1 Connecting Your Router to Your Broadband (Internet) Service

1. Connect one end of your coaxial cable to the coax connection on you wall. Connect the other end of the coaxial

cable to the connector marked Coax on the Router.

2. Connect the power supply cord to the power connector marked 12 VDC on the back of the Router. Plug the other

end of the power supply into an AC wall socket, and then turn on the Router by pressing the Off/ON switch on

the back of the Router.

3. Check to see if the Router’s POWER LED is solid green. This indicates that the Router is powered on.

4. Check to see if the Router’s Coax WAN LED is solid green. This means the COAX connection is functioning

properly. (Note: Your Coax WAN Led may also be amber which is acceptable)

Now that you have connected your Router to your broadband service and turned on the Router, you can connect

Ethernet and Wireless devices to the Router, allowing for Internet connection throughout your home without

disrupting your cable or satellite television services. Refer to the following sections for instructions on connecting

devices to your Router:

• Section 5.2 explains how to connect Ethernet devices to your broadband Router.

• Section 5.3 explains how to connection Wireless devices to your broadband Router.

5.2 Connecting Ethernet Devices to Your Router

To connect PCs to your Router using 10/100-BaseT Ethernet installation, please follow the steps below:

1. Connect your Router to your broadband service as explained in section 5.1.

2. Connect the yellow Ethernet cable (provided with your kit) from any one of the four Ethernet jacks marked 1, 2,

3, 4 on the back of the Router to the Ethernet port on your computer. Turn on the computer.

NOTE: Use any of the four LAN Ethernet jacks on the Router’s rear panel; each jack serves as an Ethernet

switch. Repeat this step to connect up to three additional PCs to the Router.

3. Check to see if the Router’s POWER LED is solid green. This indicates that the Router is powered on.

4. Check to see if any of the Router’s ETHERNET LEDs (1,2,3,4) are solid green. Solid green indicates that the

Ethernet connection is functioning properly. Check the ETHERNET LED for each Ethernet jack to which you

are connected at the rear of the Router.

5. Check to see if the Router’s COAX WAN LED is solid green (or flashing amber). This means the Coax

connection is functioning properly.

6. After you have logged on to you account and established an Internet connection, as explained later in this

document, check to see if the Router’s INTERNET LED is solid green. Solid green indicates that the Internet

link has been established.

Congratulations! You have completed the steps to connect Ethernet devices to your Router. Now proceed to section 6 to

access your Router’s Web pages.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Verizon FiOS 9100EM Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info