Bedienungsanleitung Vermeiren Ceres 3 (Seite 23 von 172) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

578238

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

Ceres 3 Deluxe, Ceres 4 Deluxe

2015-06

Page21

3.7 Tyre changing

L CAUTION: There must be no air in the tube before it can be removed.

L CAUTION: Risk of damage - If handled improperly, the rim might be damaged.

Note the following before inserting the new tube:

Check the rim bed and the inside wall of the tyre for foreign matter and clean these properly if

necessary. Check the condition of the rim bed, especially around the position of the air valve. Please

use only genuine original replacement parts. No liability is accepted for damage caused by non-

genuine replacement parts. Kindly contact your specialist dealer.

Assembly:

L WARNING: Risk of injury - Check that the pressure is correct.

L CAUTION: Risk of injury - Make sure that no objects or body parts are pinched between the

tyre and the rim when mounting a tyre.

L WARNING: Risk of injury - Make sure all screws are firmly secured by hand before driving

with your scooter. Screw adhesive (ex. Loctite) should be applied to the screws on the

flange. Screw adhesive will only work if the thread is free of grease and particles.

DISMANTLING

1. Unscrew and remove the middle screw

 that attach the wheel , , ,  and

flange  to the scooter.

2. Let the air out of the wheel by lightly

pressing the pressure pin on the valve.

3. Unscrew the 4 screws  of the rim to

separate the rim sides ,  and flange

.

ASSEMBLY

Insert the partly-filled inner tube into the tyre.

1. Connect the two sides of the rim ,  through the tyres and place the flange against the tyre and

screw them back again with the 4 screws .

2. Put the air valve through the hole for it in the rim.

3. Put the wheel , , ,  and flange  back on the scooter and secure these connection with the

middle screw . Inflate the wheel to the recommended tyre pressure.

Check all around on both sides that the tube is not pinched between the rim and the edge of the tyre.

Lightly push the air valve inwards and pull it out again to make sure that the tyre is positioned properly

in the region of the air valve.

To ensure that the wheel is inflated correctly, admit only so much air initially that the tyre can still be

easily pushed inwards by using your thumbs. If the check-lines are equidistant from the edge of the

rim on both sides of the tyre, then the tyre is centered properly. If not - let out the air and position the

tyre afresh. Now the tyre can be inflated to its full operating pressure (note the maximum) and the

valve cap should be replaced.

Only an expert can guarantee correct assembly. Work not done by your specialist dealer, would void

any warranty claims.

When inflating the tyres, always check that the pressure is correct. The correct pressure is given on

the tyre walls.

Use only inflating equipment which complies with regulations and indicates the pressure in bar. We do

not accept any liability for damage caused by using inflation equipment not supplied by the

manufacturer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermeiren Ceres 3 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vermeiren Ceres 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info