Bedienungsanleitung Vermeiren Timix (Seite 8 von 28) (Englisch)

514920

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Timix

2021-05

Before use

4. If luggage and passenger compartments are not separated or enclosed, fasten the wheelchair

frame securely to the vehicle using the 6-points strap-tie-down system (see Figure 1).

2.4.4 Transport by vehicle, as seat for user

The wheelchair has passed the crash test of ISO 7176-19: 2008 and, as such, has been

designed and tested for use only as forward-facing seat in a motor vehicle.

The wheelchair is tested dynamically with the ATD (anthropomorphic test device) using a 6-

points strap-tie system and a 3-point occupant-restraint system. Nevertheless, the user

should preferably be transferred to one of the seats inside the vehicle and use the vehicle’s

restrain system. The wheelchair should be stored as luggage in a separate (cargo)

compartment, see §2.4.3 .

Risk of injuries and damage

Use wheelchair's pelvic belt and the applicable three-points belt in the vehicle to prevent head

and chest impacts with the vehicle.

Do not use postural supports to restrain the user in the vehicle unless they are labelled as being

in accordance with the requirements specified in ISO 7176-19:2008.

Following involvement in any type of vehicle collision, have your wheelchair inspected by the

specialist dealer or manufacturer’s representative before reuse.

Securing the wheelchair

1. Make sure that the vehicle has a suitable wheelchair 6-points strap-tie-down and occupant-

restraint system conform ISO 10542, and that both systems are not frayed, contaminated,

damaged or broken.

2. Use the operating console to return your wheelchair to stable position, see §3.5.

3. Remove all mounted accessories such as trays and respiratory equipment and secure them

in a safe place. If not possible, secure them to the wheelchair but positioned away from the

occupant with energy-absorbing padding placed between tray and user.

4. Use a ramp to drive the wheelchair (with user) in the vehicle according to the instructions in

§3.2.1.

5. Position the user facing forward in the travelling direction, centrally between the tie-down rails

mounted in the floor of the vehicle.

6. Make sure that the user is sitting as upright as possible. If the user's condition prevents this,

carry out a risk assessment to evaluate the user's safety during transit.

7. Turn the operating console OFF and make sure that the free-wheel lever is in braking mode,

see §3.4.

8. The location of each securement point on the wheelchair is marked with the

following symbol:

9. Verify that the tiedown end-fitting is compatible with the wheelchair securement points.

10. Mount the front securement straps according to the instructions of the strap-system

manufacturer at the indicated place (figure 1).

11. Turn free-wheel lever in free-wheel position and roll the wheelchair backwards to pull the front

straps tight, see §3.4.

12. Mount the back securement straps according to the instructions of the strap-system

manufacturer at the indicated place (figure 1).

13. Turn free-wheel lever back in braking position, see §3.4.

WARNING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermeiren Timix Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vermeiren Timix

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info