Bedienungsanleitung Vermont Castings Intrepid - Gas (Seite 8 von 64) (Englisch)

815509

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

883-90-30007474Vermont Castings • Intrepid DV-IFT Owner’s Manual_R28 • 11/23

Horizontal Termination

Except for straight-through the wall vent installations. The

vent must rise vertically a minimum of 24” (610 mm) after

the rst elbow directly o󰀨 the back of the unit, before the

next elbow. The horizontal run may extend up to 20’ (6 m)

and include a vertical rise of up to 40’ (12 m), Figure 2.8.

• Horizontal termination must also meet the criteria

shown in Figures 2.10 and 2.11.

• Approved vent systems must terminate above and

including the heavy line, Figure 2.8.

• Two 45° elbows may be substituted for each single 90˚

elbow.

• With a rise between 2’ - 5’, one 90° or two 45° elbows

may be used (Excluding the rst elbow directly o󰀨 the

back of the unit.

• 24" maximum horizontal termination directly o󰀨 back.

• Corner installation using 45° elbow, maximum horizontal

after elbow is 24 inches.

F.GasSpecications G. Vent Terminations & Clearances

GasSpecications

Model Fuel

Gas

Control

Max.

Input

BTU/h

Min.

Input

BTU/h

INDVR Series Nat Millivolt 17,000 12,500

INDVR Series LP Millivolt 16,000 12,000

INDVR-IFT Nat IFT 17,000 12,500

INDVR-IFT LP IFT 16,000 12,000

The installation must conform with local codes or, in the

absence of local codes, with the National Fuel Gas Code,

ANSI Z223.1/NFPA 54 - latest edition. (EXCEPTION:

Do not derate this appliance for altitude. Maintain the

manifold pressure at 3.5” w.c. for Natural Gas and 10”

w.c. for Propane.)

High Elevations

Input ratings are shown in BTU per hour and are

certiedwithoutderationforelevationsupto4,500

feet(1,370m)abovesealevel.

For elevations above 4,500 feet (1,370m) in USA,

installationsmustbeinaccordancewiththecurrent

ANSI Z223.1/NFPA 54 and/or local codes having

jurisdiction.

In Canada, please consult provincial and/or local

authorities having jurisdiction for installations at

elevationsabove4,500feet(1,370m).

Air Shutter Setting

Minimum injector air inlet opening

Model Natural Gas LP(Propane)

INDVR Series 1/2 Open 1/2 Open

Gas Inlet and Manifold Pressures

Natural Gas LP(Propane)

Inlet Minimum 5.0" W.C. 11.0" W.C.

Inlet Maximum 14.0" W.C. 14.0" W.C.

Manifold Pressure 3.5" W.C. 10" W.C.

Improper installation, adjustment, alteration, service

or maintenance can cause injury or property damage.

Refer to this manual for correct installation and

operational procedures. For assistance or additional

information consult a qualied installer, service

agency, or the gas supplier.

WARNING

Figure 2.8 - Horizontal vent termination window.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Vertical Run (in feet)

Measured after the first elbow. (Transition elbow)

Horizontal Run (in feet)

ST134a

FDV28

Horizontal

vent run

12/3/99 djt

areas modified

1/11/00 djt

May use up to

four 90° Elbows

(Including elbow

directly o󰀨 back of

unit.)

Two 90°

Elbows

Unacceptable

Venting Conguration

Unacceptable

Venting Conguration

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermont Castings Intrepid - Gas Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info