Bedienungsanleitung Vermont Castings Intrepid - Gas (Seite 14 von 64) (Englisch)

815509

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

1414 3-90-30007474Vermont Castings • Intrepid DV-IFT Owner’s Manual_R28 • 11/23

B.AssemblingtheStove:

Tools Required

• Phillips screwdriver (stub)

• Utility knife

• Metal drill bit: size 28 (.140"/3.5mm)

• Flat-blade screwdriver

• Power drill

• Reciprocating saw

• 9/16" wrench

• 1/2” Wrench

Parts Bag Contents:

• Three (3) Vent Screws

• Two (2) Switch bracket screws

• Wood handle w/insert lifter (handle for operable door)

• Restrictor Plate

• 4" Starter pipe

• Wireless Remote

• Three (3) Phillips round-head bolts, 1/4"- 20 x 1/2"

• One (1) Tube of Vent Gasket Cement

• Four (4) CS, Hex Hd 3/8-16 x 1 Gr 2-Z

• Four (4) Washer, Fl 3/8-Z

• Owner’s Installation and Operating Manual

Unpack Stove

Using a 1/2” wrench remove the (4) lag bolts installed through

the shipping brackets and into the skid. Using a 7/16” wrench

loosen the (4) bolts where the shipping brackets meet the

base of the unit. Once loosened, tilt the unit slightly and

remove the (2) front bolts, washers and shipping brackets.

Use the (4) 1/4-20 x 1” Bolts and 1/4” washers supplied in

the manual bag to install the legs where the brackets were

once installed. Repeat previous step to install the rear legs.

WARNING

Only the IFT appliance is equipped with a three-prong

(grounded) plug for your protection against shock hazard

and should be plugged directly into a properly grounded

three-prong receptacle. Do not cut or remove the ground-

ing prong from this plug.

C.VentingSystemAssembly

CAUTION

All HHT Direct Vent Stoves have been tested and

approved to ANSI/CSA Standards and will operate safely

when installed in accordance with this instruction manual.

Read all instructions before starting installation, then follow

these instructions carefully to maximize stove performance

and safety. Report damaged parts to your dealer.

Important Safety Information

The termination cap MUST be vented directly to the outside.

The termination kit MUST NEVER be connected to a chimney

ue(s) servicing a separate solid-fuel burning appliance or

any other appliances.

• Termination cap MUST NOT be recessed into a wall,

Figure 3.1.

• The installation must conform with local codes or in the

absence of local codes, with the National Fuel Gas Code,

ANSI Z223.1 (in the United States) or with the current

installation code CSA B149 (in Canada).

• These models are approved to use HHT direct vent

pipe components, HHT termination kits and DuraVent

components. No other venting system components may

be used.

• Horizontal runs must be supported every 3 feet (914 mm)

using wall straps. Vertical runs must be supported every

8 feet (2.4 m) using wall straps. Slip wall straps loosely

on to pipe. Attach straps to framing members using nails

or screws. Tighten nut/bolt to secure pipe.

• The stove and venting system should be inspected

before initial use and at least annually by a qualied

eld service person. Inspect the external vent cap on a

regular basis to make sure that no debris is interfering

with the airow. Inspect entire venting system to ensure

proper function.

WARNING

Always maintain minimum clearances around vent

systems. Rear Vent Vertical Side wall: Horizontal sections

of this vent system require a minimum of 3” (76 mm)

clearances to combustibles at the top of the ue and 1”

(25 mm) clearance at the sides and bottom until the ue

penetrates the outside wall. A minimum 1” clearance all

around the ue is acceptable at this point of penetration.

FOR VERTICAL RUNS, maintain a 1” (25 mm) minimum

clearance to all sides. Do not pack the open air spaces

around the stove or ue with insulation or other materials.

Any horizontal run must have a 1/4” rise for every one (1)

foot of run towards the vent termination. Never run the

vent level or down.

WARNING

Failure to follow these instructions may create a possible

re hazard and will void the warranty.

WARNING

Any common venting of this gas appliance with other gas

appliances is not allowed.



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermont Castings Intrepid - Gas Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info