Bedienungsanleitung Vermont Castings Intrepid - Gas (Seite 19 von 64) (Englisch)

815509

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

1919 3-90-30007474Vermont Castings • Intrepid DV-IFT Owner’s Manual_R28 • 11/23

Vent Termination Below Grade:

Install Snorkel Kit #SLP-SNORK when it is not possible to

meet the required vent termination clearances of 12" (305

mm) above grade level. The snorkel kit will allow installation

depth of down to 7" (178 mm) below grade level. The seven

inches is measured from the center of the horizontal vent

pipe as it penetrates the wall. If the venting system is

installedbelowgrade,awindowwellmustbeinstalled

with adequate and proper drainage.

NOTE: Be sure to maintain side wall clearances and vent

run restrictions. Refer to Figures 2.3 thru 2.6.

1. Establish the vent hole through the wall.

2. Remove soil to a depth of approximately 16" (406 mm)

below the base of the snorkel. Install a window well (not

supplied). Rell the hole with 12" (305 mm) of coarse

gravel and maintain a clearance of at least 4" (102 mm)

below the snorkel, Figure 3.14.

3. Install the vent system as described in Figures 3.2 thru

3.14.

4. Be sure to make a watertight joint around the vent pipe

joint at the inside and outside wall joints.

5. Apply high temperature sealant around the inner and

outer snorkel collars. Join the pipes and fasten the

snorkel termination to the wall with the screws provided.

6. Level the soil to maintain a 4" clearance below the

snorkel.

7. If the foundation is recessed, use extension brackets

(not supplied) to fasten the lower portion of the snorkel.

Fasten the brackets to the wall rst, and then fasten to the

snorkel with self-tapping #8 x 1/2" sheet metal screws.

Extend the vent pipes out as far as the protruding wall

face, Figure 3.14.

Figure 3.14 - Use extension brackets to mount snorkel against

recessed wall.

ST219

snorkel detail

12/6/99 djt

Recessed Wall

Sheet Metal

Screws and

Bracket

Wall Screws

and Anchors

Waterproof Seal

Around Pipe

Firestop

Finishing

Collar

7" Pipe

Wall Plate

VerticalThrough-The-RoofApplication/Installation:

Note: Refer to Figures 2.8 thru 2.10 for restrictor plate

adjustments for vertical vent runs.

This gas stove has been approved for:

• Vertical installations up to 40 feet (12 m) in height. Up to

a 10 feet (3 m) horizontal vent run can be installed within

the vent system using a maximum of two 90° elbows,

Figure 3.15.

• Up to two 45° elbows may be used within the horizontal

run. For each 45° elbow used on the horizontal plane,

the maximum horizontal length must be reduced by 18"

(450 mm).

Example: Maximum horizontal length:

No elbows = 10' (3 m)

1 x 45° elbow = 8.5' (2.6 m)

2 x 45° elbows = 7' (2.1 m)

• A minimum of an 8 feet (2.5 m) vertical rise is required,

Figure 3.15.

• Two sets of 45° elbow o󰀨sets may be used within the

vertical sections. From 0 to a maximum of 8 feet (2.5 m)

of vent pipe can be used between elbows, Figure 3.16.

• SLP-HVS supports o󰀨sets. This application will require

that you rst determine the roof pitch and use the

appropriate starter kit. (Refer to Venting Components

list.)

• The maximum angular variation allowed in the system is

270°, Figure 3.16.

• For the minimum height of the vent above the highest

point of penetration through the roof, Figure 3.16.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermont Castings Intrepid - Gas Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info