Bedienungsanleitung Vermont Castings Radiance Series (Seite 15 von 56) (Englisch)

815507

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

1515 3-90-30007498Vermont Castings • Radiance RADVT Installation Manual_R32 • 10/23

Before You Start

Plan your installation. Set the stove in place and survey how

to best vent the unit. Select the appropriate termination kit

and vent pipe for the installation. Read these instructions

and the stove Owner’s Manual before beginning installation.

After vent conguration has been decided, begin attaching

pipe to unit.

Items required for installation:

Tools:

Hammer Saw and/or saber saw

Level Measuring Tape

Electric drill and bits Pliers

Square

Building Supplies:

Framing materials

Wall nishing materials

Caulking Material (noncombustible)

• These models are approved to use HHT direct vent

pipe components, HHT termination kits and DuraVent

components. No other venting system components may

be used.

• Horizontal runs must be supported every 3 feet (914 mm)

using wall straps. Vertical runs must be supported every

8 feet (2.4 m) using wall straps. Slip wall straps loosely

on to pipe. Attach straps to framing members using nails

or screws. Tighten nut/bolt to secure pipe.

• The stove and venting system should be inspected

before initial use and at least annually by a qualied

eld service person. Inspect the external vent cap on a

regular basis to make sure that no debris is interfering

with the airow. Inspect entire venting system to ensure

proper function.

Outside Wall

Finishing Material

(Vinyl Siding, etc.)

Figure 3.1 - Termination cap on wall

General Information

The Radiance is approved for installation only with the vent

components listed under Section A “Venting Requirements

& Options”. Follow the vent component instructions exactly.

For U.S. installations: The venting system must conform with

local codes and/or the current National Fuel Gas Code, ANSI

Z223.1/NFPA 54.

For Canadian installations: The venting system must conform

to the current CSA B149.1 installation code.

Install the starter Pipe

1. Attach the starter to the stove.

2. Place a 3/8” bead of sealant around the inside of the cast

starter collar. Stove cement is provided in the manual

bag for this purpose. Insert the 6-5/8” outer adapter into

the cast outer starting collar and press down rmly.

3. Install the CCSLP Outer Adapter Pipe.

4. Place a 3/8” bead of sealant around the 4” crimped

end of the starter collar on the stove. Stove cement is

provided in the manual bag for this purpose. Attach the

SLP pipe to the adapter, and secure by aligning adapter

and pipe seams, pressing down rmly until pipe stops,

and twisting to lock into place, Figure 3.2.

WARNING

Any horizontal run must have a 1/4” rise for every one (1)

foot of run towards the vent termination. Never allow the

vent pipe to run down. This could cause high temperatures

and may present a re hazard.

WARNING

Termination cap must be positioned so the embossed

arrow is pointed up.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermont Castings Radiance Series Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vermont Castings Radiance Series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info